18 |
P a g e
M o d e l V B 9 0 0
ADJUSTMENTS
Apron Chain
FIGURE 10. ADJUST APRON CHAIN
A1
–
The apron chain is adjusted by (4) adjuster bolts
located on the front of the box frame, Figure 13. Adjust the
bolts so the chain is elevated above the plastic slide rails
for 20” as illustrated in Figure 10. When there is no more
adjustment left on the adjuster bolts, loosen the nuts and
push the bolts in as far as they will go. Then remove a link
from each chain and readjust.
NOTICE!
Apron chains must be adjusted equally so that it
runs centered on the front nylon rollers.
LUBRICATION
L1
–
Grease bearings on top of Vertical Beaters, one
pump every 8 hours, both sides by grease lines.
L2
–
Maintain oil level in apron drive gearbox, located at
right, rear of spreader. Check at sight glass. When
required, refill with SAE 85-140 Moly Fortified gear lube or
Synthetic SAE 75-90 gear lube.
L3
–
Grease 6 bearings on drive shaft under spreader
box, one pump every 8 hours. These bearings are
accessed by grease lines, 5 places on RH side of
machine, 1 on LH.
L4
–
Grease 2 bearings at front of driveline connecting to
the PTO shaft, on RH side of housing. Grease these
bearings one pump every 8 hours.
L5
–
Grease Pivot Hitch 2 pumps every 8 hours, each
grease zerk.
L6 -
Grease the apron drive shaft, both sides of the
spreader by the grease lines, 4 locations. 5 pumps every 8
hours.
L7-
Grease the axle at both sides of the spreader by the
grease lines, 4 locations, 10 pumps every 8 hours.
L8 -
Maintain oil level in vertical beater gearbox at sight
level gauge. When required, refill with SAE 85-140 EP
gear lube or Synthetic SAE 75-90 gear lube.
L9 -
Grease cross bearings on yoke (both ends of PTO
shaft) 1 pump every 8 hours. Grease telescoping shaft
through slot in center of guard, 4-5 pumps every 8 hours.
Figure 15.
L10 -
Special attention should be paid to lubricating the
constant velocity PTO drive shaft assembly. Figure 15.
FIGURE 15. PTO LUBRICATION
NOTICE!
SPREADER MUST BE SITTING LEVEL FOR AN
ACCURATE OIL CHECK.
TO CHECK OIL LEVELS, PARK SPREADER ON
LEVEL GROUND, AND USE JACK TO RAISE /
LOWER THE SPREADER BODY UNTIL IT IS
COMPLETELY LEVEL.
Summary of Contents for VB900
