18 |
P a g e
M o d e l M 3 2 3 0
UNHOOKING FROM TRACTOR
1. Park the spreader, set tractor parking brake, and turn off all power.
2. Park your spreader on level ground and place blocks ahead of and behind the wheels.
3. Remove jack pin and move to vertical position, raise jack until hitch is not resting on tractor drawbar.
4. DO NOT UNHITCH A LOADED SPREADER LEAVING IT SUPPORTED BY ONLY THE JACK!
5. Disconnect the PTO shaft, hydraulic hoses, electrical plug, and safety chain. Remove pin.
MAINTENANCE, ADJUSTMENTS, & LUBRICATION
WHEEL & TIRE MAINTENANCE
WHEELS:
Check after first hour of towing and periodically thereafter. The wheel studs should be torqued to 170
foot pounds in a crisscross pattern.
TIRE PRESSURES
:
22.5x8.25 Recommended Pressure: 45
– 60 PSI MAX
W14Cx16.1 Recommended Pressure: 36 PSI MAX
425-65R Recommended Pressure: 45 - 90 PSI MAX
Wheel Hub Lubrication
Remove the wheels and hubs annually. Clean out old grease and repack bearing cones with quality EP grease.
Put a ¼” film of grease on the bearing cups and reassemble. If your hubs have grease zerks, do not lube them.
Grease builds up in the hub and will eventually damage the seal when expansion from heat occurs.
Lock Ring Rim
Removing, replacing and repairing industrial tires and rims with lock rings can be dangerous without proper tools,
equipment and training to perform this service. It is recommended that this work be performed only by a qualified
tire repair shop.
MANDATORY SAFETY SHUTDOWN PROCEDURE
BEFORE unclogging, cleaning, adjusting, lubricating or servicing the unit:
1. Disengage the tractor PTO.
2. Shut off the tractor engine, remove the ignition key and take it with you.
3. Wait for all movement to stop.
4. Remove the Telescoping PTO Drive and ALL power connections from the tractor.
ONLY when you have taken these precautions can you be sure it is safe to proceed.
Failure to follow the above procedure could lead to death or serious bodily injury.
Summary of Contents for M3230 Tandem
