background image

4. 

Feed control knob/wire through the  

T-handle until spring touches the round 
hole. CAUTION: Do Not Compress 
Spring At This Time.

 

Feed wire through 

the square handle tube. Be sure wire 
passes above the bolts in the handle 
brace. Secure T-handle to the tube with 
(1) 1/4-20 x 2 1/4” hex bolts, (2) washers, 
and (1) hex nut in the  holes. Remove 
caution label and push the thumb 
release toward the center and push 
down knob and shutoff spring until 
knob latches.

 

 

CAUTION: Once knob is latched,  

do not move thumb release until you have 

completed in step #5. 

 

Control Knob & 
Wire Assembly 

Spring 

Thumb 
Release 

1/4-20 x 2 1/4” 
Bolt & Washer 

1/4-20 Hex Nut 

& Washer 

Remove Caution 
Label 

5

Slide wire retaining clip onto wire as shown. 

Insert wire through hole shutoff plate. Slide wire 
retaining clip over shutoff plate and wire until 
the clip locks into place.

 

Wire Clip 

Shutoff Plate 

Wire 

6

Install handle grips onto the handle 

as shown. Soapy water will ease 
installation. (Do not use petroleum 
based products). Insert screen into 
hopper by sliding it under the screen 
clips.

 

Handle Grips 

Screen 

Screen Clips 

Summary of Contents for 38100









Reviews: