Meyer Sound 750-LFC Operating Instructions Manual Download Page 38

750-LFC OPERATING INSTRUCTIONS

38

During startup, the LED flashes green 10 times.

If the loudspeaker has not yet been discovered on the 
RMS network, the LED is not lit after startup.

If the loudspeaker has been successfully discovered on 
the RMS network, the LED flashes green continuously 
and flashes more rapidly with increased data activity.

When the loudspeaker is winked, either by clicking the 
Wink button in Compass RMS or by pressing the Identify 
button on the RMS user panel, the LED is solid green. 
The LED remains solid green until the loudspeaker is 
unwinked.

TIP: 

The Wink function is useful for identifying 

the physical loudspeaker corresponding to a 
loudspeaker icon in Compass RMS.

Remote Mute Switch

The recessed Remote Mute switch on the 750-LFC RMS 
module (Figure 33) determines whether Compass RMS can 
control muting and soloing of the loudspeaker. The 750-LFC 
ships from the factory with the switch enabled.

Disable:

 When the Remote Mute switch is set to Disable 

(to the left), the loudspeaker cannot be muted or soloed 
from Compass RMS.

Enable:

 When the Remote Mute switch is set to Enable 

(to the right), the loudspeaker can be muted and soloed 
from Compass RMS.

NOTE: 

Compass RMS has a preference that 

can be set to disable Mute and Solo functions, 
eliminating any possibility of accidentally mut

-

ing loudspeakers.

RMS Network Connectors

The Weidmuller 2-conductor, locking connectors transfer 
data to and from the RMS network. Two connectors are 
provided to allow for easy connection of multiple 
(daisy

-

chained) loudspeakers on the network. Included with 

each RMS-equipped loudspeaker are RMS cable 
connectors and mounting blocks for constructing RMS 
cables. The mounting blocks allow the Weidmuller 
connectors to be securely attached to the RMS module with 
screws.

NEURON ID FOR RMS MODULE

Each RMS module has a unique 12-character Neuron ID 
(NID) that identifies the loudspeaker on the network. The 
NID is automatically detected by RMServer but can also be 
entered manually, if necessary, when configuring RMS 
systems in Compass RMS without loudspeakers present. 
The NID label is located on the RMS user panel near the 
orange Network connectors.

RESETTING THE RMS MODULE

You can use the Identify button to reset the 750-LFC RMS 
module when powering on the loudspeaker. This action will 
cause the module to be removed from the RMS network.

To reset the RMS module:

1. Power down the loudspeaker.

2. Press and hold the Identify button.

3. While continuing to hold down the Identify button, power 

on the loudspeaker.

4. After the Wink/Status LED flashes on and off, release the 

Identify button. The RMS module is reset and the loud

-

speaker is removed from the RMS network.

Figure 33: Remote Mute Switch

Summary of Contents for 750-LFC





















































Reviews: