Meyer Sound 40.010.971.01, Assembly Manual

Page: 11 / 96

MG-MINA/LINA/750-LFC GRID ASSEMBLY GUIDE
3
Replacement Parts
Any component found to be defective, or any safety-related component suspected to be defective, should be replaced with
the equivalent, approved part. Parts specific to a QuickFly system should be ordered directly from Meyer Sound. No
attempt should be made to substitute what appears to be equivalent or “mostly the same” generic replacements. Some
parts used in QuickFly systems are identical to those used in other rigging applications. To the best of our knowledge, most
of these suppliers are reputable and their products are reliable. However, Meyer Sound has no way of assuring the quality of
products made by these various suppliers. Therefore, Meyer Sound is not responsible for problems caused by components
that were not supplied by Meyer Sound.
Training
QuickFly systems are relatively straightforward and easy to use. However, they should only be used by persons trained in
the use of loudspeaker rigging systems, who have mastered key points of assembly, rigging and flying.
LINA AND 750-LFC RIGGING OPTIONS
Table 1 summarizes the available rigging options for LINA and 750-LFC loudspeakers.
Table 1: LINA and 750-LFC Rigging Options
Model Weight Features Required Quick-
Release Pins
Required
Shackles
MRK-750
rigging kit
PN 40.271.009.01
25 lb
(11.3 kg)
Upgrade kit to allow the 750-LFC to be flown and
groundstacked with the MG-LINA//750 grid; includes hardware
for the upgrade, captive GuideALinks and quick-release pins.
0.25 in x 0.53 in,
(black button)
PN 134.039
qty 10 included
—
MG-MINA/LINA/750-LFC
multipurpose grid
assembly kit
(PN 40.207.101.01)
39 lb
(17.7 kg) With some restrictions, flies up to 16 LINA cabinets at a 5:1
safety factor and BGV C1 with some angle restrictions
(additional load ratings are possible—use MAPP XT to verify
load ratings); supports mixed arrays of LINAs and 750-LFCs
without transition hardware; accommodates a variety of pickup
configurations with four corner and 11 center pickup points; can
also be used for groundstacking. 0.25 in x 0.90 in
(black button with 6 in
lanyard),
PN 134.036,
qty 8 included
5/8-inch or
3/4-inch
MG-MINA/LINA/750-LFC
multipurpose grid with
GLK-750-LFC assembly
kit
(PN 40.207.101.02)
39 lb
(17.7 kg) With some restrictions, flies up to 16 LINA cabinets at a 5:1
safety factor and BGV C1 with some angle restrictions
(additional load ratings are possible—use MAPP to verify load
ratings); supports mixed arrays of LINAs and 750-LFCs without
transition hardware; accommodates a variety of pickup
configurations with four corner and 11 center pickup points; can
also be used for groundstacking; includes MG-MINA to 750-
LFC Grid Link. 0.25 in x 0.90 in (0.25 in
x 0.90 in (black button
with 6 in lanyard),
PN 134.036,
qty 2 included
5/8-inch or
3/4-inch
GLK-750-LFC
grid link upgrade kit
PN 40.207.301.01
2 lb
(0.9 kg)
Includes two grid links to upgrade existing MG-MINA/LINA grids
(PN 40.207.101.01). These 2 rear links effectively increase the
load rating for the grid when attaching 750-LFCs. Alway use
MAPP to verify load ratings. 0.25 in x 0.90 in (black
button with 6 in lanyard),
PN 134.036,
qty 2 included
—
MUB-MINA/LINA
mounting U-Bracket kit
(PN 40.207.030.01)
5.8 lb
(2.63 kg) Mounts up to five LINA cabinets for front-fill or under-balcony
coverage with up to 20 degrees of tilt. Pole-mounts up to two
cabinets using the 35MM Pole Stand Adapter (not included). — —
MYA-MINA/LINA
Yoke kit
(PN 40.207.104.01)
12.9 lb
(5.85 kg) Suspends arrays of up to three LINA cabinets from a single
point and pole-mounts,
using the 35MM Pole Stand Adapter
(not included), up to two cabinets on top of a 750-LFC. The
yoke includes two bracketing options: the MPA-2 for attaching
to two cabinets, and the MPA-3 for attaching to one or three
cabinets.
— —