manualshive.com logo in svg

Metz Connect EWIO 2, User Manual

Share
Download
Metz Connect EWIO 2 User Manual Download Page 60

 

 

 

 

 

EWIO

2

 User Manual 

V 1.1 | Stand 10/2020 

 Seite 60 von 96 

 

 

METZ CONNECT GmbH | Im Tal 2 | 78176 Blumberg | Germany  
Tel. +49 7702 533-0 | Fax +49 7702 533-433 
For additional documentations look at www.metz-connect.com 

10.5.3.6.

 

Characteristics 

In the menu window "Characteristic" a user-defined sensor characteristic curve can be defined. 

It can be selected as "User defined" in the menu item "Analog inputs", see chapter 

10.5.3.2.

 in 

the pop-up table "Config". The actual value shown there is then interpolated using this table. 

 

In the pop-up menu "Range" the physical quantities voltage, voltage with connected pull-up 

resistor, current and resistance linear or exponential are available. 
In the input field "Unit" a unit can be entered. 
In the input fields "x" and "y" the given value pairs can be edited. Here in the example, the X-
value as a support point for the temperature and the Y-value for the corresponding resistance 

value. 
Up to 10 value pairs can be defined by activating the action field "Add Node". 
By activating the action field with the trashcan symbol, interpolation points can be removed. 
The value pairs are only accepted when the action field "Save" is pressed. 
 

10.5.3.7.

 

Record 

In the menu window "Record" stored data of inputs and outputs can be displayed, which have 

been configured for an acquisition as described in chapters 

10.5.3.1.

 to 

10.5.3.4.

  

Summary of Contents for EWIO 2

































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands