manualshive.com logo in svg

Metz Connect EWIO 2, User Manual

Share
Download
Metz Connect EWIO 2 User Manual Download Page 55

 

 

 

 

 

EWIO

2

 User Manual 

V 1.1 | Stand 10/2020 

 Seite 55 von 96 

 

 

METZ CONNECT GmbH | Im Tal 2 | 78176 Blumberg | Germany  
Tel. +49 7702 533-0 | Fax +49 7702 533-433 
For additional documentations look at www.metz-connect.com 

 

By pressing the blue bar with the name and the set address of the expansion module, the 

display can be opened and closed with the other IOs. 
 
Attention ! 

With the extension module MR-SI4 only digital states are displayed. 

 
 

 

10.5.3.2.

 

Analog Inputs 

 

The menu window "Analog inputs" lists the available analog inputs.  
The port name shown indicates the input channel. The designation in brackets corresponds to 

the terminals on the EWIO

2

. 

The text field is intended for a user-defined description of the signal connected to the input. 

The configuration-dependent process value at the input is displayed live. 

The input configuration can be changed in the pop-up menu. 
Configurations are available for 

- Voltage measurement for 0 - 10 Volt with unit Volt or percent 
- Voltage measurement for 0 - 5 Volt and switched on PullUp resistor for  

  Semiconductor sensor with unit Volt or percent 

- Resistance measurement in the range 40 Ohm to 4 MegaOhm with unit Ohm. 
- Current measurement for 0 or 4 - 20 mA with unit milliAmpere or percent 

Summary of Contents for EWIO 2

































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands