Metso Jamesbury Valv-Powr Value-Line D VPVL Series Installation Maintenance And Operating Instructions Download Page 16

Subject to change without prior notice.

Neles Finland Inc.

Europe,  Vanha Porvoontie 229, P.O. Box 304, FI-01301 Vantaa, Finland. Tel. +358 20 483 150. Fax +358 20 483 151

North America,  44 Bowditch Drive, P.O. Box 8044, Shrewsbury, MA  01545, USA. Tel. +1 508 852 0200. Fax +1 508 852 8172

South America, Av. Independéncia, 2500-Iporanga, 18087-101, Sorocaba-São Paulo, Brazil. Tel. +55 15 2102 9700. Fax +55 15 2102 9748 

Asia Pacific, 238B Thomson Road, #17-01 Novena Square Tower B, Singapore 307685. Tel. +65 6511 1011. Fax +65 6250 0830

China, 11/F, China Youth Plaza, No.19 North Rd of East 3rd Ring Rd, Chaoyang District, Beijing 100020, China. Tel. +86 10 6566 6600. Fax +86 10 6566 2583

Middle East, Roundabout 8, Unit AB-07, P.O. Box 17175, Jebel Ali Freezone, Dubai, United Arab Emirates. Tel. +971 4 883 6974. Fax +971 4 883 6836

www.metso.com/valves

16 

IMO-553 EN

WARNING:

As the use of the actuator is application specific, a number of factors should be taken into account when selecting an actuator  

for a given application. Therefore, some of the situations in which the actuators are used are outside of the scope of this 

manual. If you have any questions concerning the use, application or compatibility of the actuator with the intended service, 

contact Metso for more infromation.

HOW TO ORDER

To specify a complete 

Valv-Powr

 Value-Line® Actuator, simply make a selection from the code boxes below. 

EXAMPLE: VPVL 400 SR4/5 B AS D, shown below, is a 59 FT•LBS 60-psi (84 N•m @ 4.2 bar) spring-return actuator with 

spring-to-close rotation, hard-anodized PTFE-coated body, polyester-coated end caps, standard temperature rating, and 

100% adjustable travel stops.

1

2

3

4

5

6

7

VPVL

400 SR4/5

B

AS

D

NOTE: for multiple options, specify them in order as listed in Item 5, for example: VPVL400 SR4/5 B HT AS Model D.

1

Product Group

VPVL

Valv-Powr  

Double-opposed Piston Actuator

2

Size

051

Select from torque table

100,200
250,300

350, 400
450, 500
550, 600
650, 700

800

3

DA

Double acting, pneumatic

SR4/5

Spring-Return 60-psi (4.1 bar) Spring-to-Close  

(CW Rotation)

SR6

Spring-Return 80-psi (5.5 bar) Spring-to-Close  

(CW Rotation)

+ Other spring rates on application

4

Exterior Protection*

B

Hard-Anodized PTFE-Coated Body &
Polyester-Coated End Caps

* Consult factory for other protection options.

5

Options

Standard Temperature Rating: -40°F to +176°F (-40°C to 

+80°C)

HT†

High-Temperature Rating: +5°F to +302°F (-15°C to 

+150°C)

LX†

Low-Temperature Rating: -60°F to +176°F (-51°C to 

+80°C)

FO

Spring-to-Open (CCW Rotation)

AS

100% Travel Stop

LD

Mechanical Safety Lockout

† HT and LX options decrease cycle life.

6

Model

D

Model D

7

Modifier Code

Standard

Summary of Contents for Jamesbury Valv-Powr Value-Line D VPVL Series

















Reviews: