Metrum Acoustics 1619b User Manual Download Page 2

 

 

All-Engineering BV 
https://metrumacoustics.com 
[email protected]  
 

Think clarity. The ADAGIO does a wonderful job of presenting even the most complex music 
in a natural and inviting manner with every last ounce of nuance intact. There’s no artificial 
sounding edge, no sense of a flat cut-out image, basically none of digital’s nastier stuff. In 
some cases, this can also come with a somewhat dark and muddy sound but that is absolutely 
not the case with the ADAGIO; 

think clarity

The ADAGIO allows you to hear into the recording and the recording’s quality. This is 
somewhat of a good news/bad news proposition in that you’ll really hear what’s there. 

Pure & Simple with Pre-Amplification

 

What more can you do after launching one of the best DAC’s available today? We are aware 
that our current flagship ADAGIO is hard to beat but at least one idea was not realized yet. 
The idea of having a decent volume control to prevent a necessary pre-amplifier could 
improve performance dramatically. However, we also know that the way of introducing such 
device in the signal chain can also have a negative effect. 

Experiments were made and as result the best sound was coming directly from our 
Transient™ modules. Even the digital approach did not convince us but still one idea was not 
tried yet. Especially in case of R2R ladder DACs it is quite easy to change the output voltage 
of the DAC by changing its reference voltage but to realize this, dedicated DAC boards were 
designed to get the best regulation possible. 

Like our PAVANE, “forward correction” techniques are used to drive both mono DAC 
boards. The result of this process is an extremely high linearity, right down to -140 dB, which 
gives the ADAGIO a realistic 24-bit dynamic range. The ADAGIO is a forward as it omits a 
pre-amplifier. It is musical, honours the Non-oversampling principle and simultaneously 
incorporating the technological progress that has been made over the years. 

The ADAGIO is build up with a double well damped frame and will avoid vibrations due to 
the use of bituminous material. Around this strong body beautiful shaped aluminium panels 
are used to make it even stronger. The chosen approach masks the use of screws from most 
important directions. As standard, a remote will be delivered to control the available digital 
inputs. 

 

note: 

The ADAGIO will reach its maximum performance after a three to four 
weeks usage.

 

 

 

IMPORTANT SAFETY INSTRUCTIONS 
1. 

Read Instructions. 

2. 

Keep these Instructions. 

3. 

Heed all Warnings. 

4. 

Follow all Instructions. 

5. 

Do not use this apparatus near water. 

Summary of Contents for 1619b













Reviews: