Metrodata DC3445 User Manual Download Page 15

Page: 15 / 17

DC3445 SPECIFICATIONS

5 DC3445 SPECIFICATIONS

5. 1 DC3445 Product Specification

Parameter

Definition

E3/DS3 LINE

Interface

G.703 compliant, Sensitivity -10dB.

E3 Line coding HDB3. DS-3 Line coding B3ZS

Interface type:

75 Ohm unbalanced coax, BNC connectors

Jitter Tolerance

Per G.823.

Barrier

EN 41003 compliant barrier provided on the E3/DS3 LINE

interface.

DTE Interface

HSSI:

50 way miniature AMP connector

Clocking options

E3/DS3 LINE port:

Circuit 113 (normally slaved to Circuit 114)

DTE port (Circuit 114):

INTERNAL, LOOP

DTE Receive timing RT:

Circuit 115 is always sourced from

the E3/DS3 Receive clock

Diagnostics

Loop Test initiated by Bit-switch

General

Definition

Power supply

100-250 VAC, 50-60 Hz, 115-45 mA or

-36 to -72 VDC, 150-70 mA

Dimensions

202 x 132 x 44 mm (w x d x h) Enclosure only

202 x 132 x 47 mm (w x d x h) Overall including feet

Environmental

Range

Ambient Temperature 0 degC to +50 degC

Storage Temperature

-20 degC to +70 degC

Relative Humidity

0% - 95% non condensing

Barometric Pressure

86 KPa - 106 KPa

Summary of Contents for DC3445


















Search results

Summary of Contents for DC3445

Reviews:

Related manuals for DC3445

Brands by name

Popular brands

Metrodata DC3445, User Manual

Search results

Summary of Contents for DC3445

Reviews:

Related manuals for DC3445

Brands by name

Popular brands