Radiance 10Mbps Redundant Interface Line Card 13
4
Install the Line Card
The Radiance 10Mbps redundant interface line card offers the ease of
plug-and-play installation and is hot-swappable. All cards must be
firmly secured to the chassis before network connections are made.
Follow the simple steps outlined below to install the line card.
NOTE: Proper grounding is recommended (i.e., wrist strap).
• Grasp the card by the front panel as shown.
• Insert the card into a slot on the chassis
making sure that the top and bottom edges of the card are
aligned with the top and bottom card guides in the chassis.
Do not force the card into the chassis unnecessarily. It
should slide in easily and evenly.
• Slide the card in until the top and bottom edges of the
front panel are flush and even with the top and bottom edges
of the chassis.
• Turn the thumbscrew clockwise until it is snug to secure the
card to the chassis. The card is now properly installed and
ready for connection to the network.
FX
PWR
RX
RX
LK
LK
M
M
FL
TX
TX
10/100
M
M
RX
LK
TX
FX
M
M
II
x
PWR
100
FD
RX
LK
T
X
TX
10/100
II
x
PWR
100
FD
RX
RX
LK
LK
T
X
M
M
FL
TX
TX
10/100
II
x
II
x
PWR
100
FD
100
FD
RX
RX
LK
LK
T
X
T
X
TX
TX
10/100
RX
LK
TX
FX
M
M
II
x
PWR
100
FD
RX
LK
T
X
TX
10/100
MGT-10
LK
AT
C
O
N
S
O
L
E
1
PWR
A
B
R
ER
FX
PWR
RX
RX
LK
LK
M
M
FL
TX
TX
10/100
M
M
PWR
RX
RX
LK
LK
M
M
FL
TX
TX
10/100
FX
M
M
PWR
M
M
OC-12
R
X
LK
LK
T
X
S
M
R
X
T
X
LX
LK
LK
PWR
1000BASE
S
M
SX
M
M
PWR
1000BASE
LK
LK
SX
M
M
LX
S
M
R
X
T
X
Card Guide
Card Guide
Slot for Management Card
Thumb Screw
Blank Panel
IMPORTANT!
Tighten thumb screw
to secure each card firmly
to chassis before making
network connections.
FX
PWR
RX
RX
LK
LK
M
M
FL
TX
TX
10/100
M
M
FX
PWR
RX
RX
LK
LK
M
M
FL
TX
TX
10/100
M
M
PWR
M
M
OC-12
R
X
LK
LK
T
X
S
M
R
X
T
X
PWR
M
M
OC-12
R
X
LK
LK
T
X
S
M
R
X
T
X
PWR
M
M
OC-12
R
X
LK
LK
T
X
S
M
R
X
T
X
PWR
M
M
OC-12
R
X
LK
LK
T
X
S
M
R
X
T
X
R
X
T
X
LK
PWR
10 BASE
M
A
I
N
AT
P
R
I
S
E
C
RESET
LK
AT
LK
AT
SEC
LK
AT
2
