background image

3

1. Dashboard
2. Nut (5mm)
3. Spring washer
4. Screw (5 x 25mm)
5. Screw
6. Strap

Be sure to use the strap to secure the 
back of the unit in place.  The strap can
be bent by hand to the desired angle.

7. Plain washer

Removing the unit

1. Frame
2. Insert fingers into the groove in the front

of frame and pull out to remove the 
frame.  (When re-attaching the frame, 
point the side with a groove downwards
and attach it.)

3. Lever

Insert the levers supplied with the unit 
into the grooves at both sides of the unit
as shown in figure until they click.  
Pulling the levers makes it possible to 
remove the unit from the dashboard.

DIN REAR-MOUNT (Method B)

Installation using the screw holes on the sides of the unit.

Fastening the unit to the factory radio 
mounting  bracket.
1. Select  a position where the screw 

holes of the bracket and the screw 
holes of the main unit become 
aligned (are fitted), and tighten the 
screws at 2 places on each side.
Use either truss screws (5 x 6mm) or
flush surface screws (4 x 6mm), 
depending on the shape of the screw
holes in the bracket.

2. Screw
3.  Factory radio mounting bracket
4. Dashboard or Console
5. Hook (Remove this part)

Note: The mounting box, outer trim ring,

and half-sleeve are not used for 
this method of installation.

1

2

6

5

4

3

7

1

3

1

(Fig. 2)

3

4

5

2

2

5

Summary of Contents for MCD-479













Reviews: