background image

7

CONNECTIONS TO BE MADE

From the 5834 harness to the aftermarket radio:

•  Connect the 

Black

 wire to the ground wire.

•  Connect the 

Yellow

 wire to the battery wire.

•  Connect the 

Green

 wire to the left rear positive speaker output.

•  Connect the 

Green/Black

 wire to the left rear negative speaker output.

•  Connect the 

Purple

 wire to the right rear positive speaker output.

•  Connect the 

Purple/Black

 wire to the right rear negative output.

•  Tape off and disregard the following (1) wire, it will not be used in this application: 

Blue

• 

For models with a 4.2-inch display screen and SYNC

®

:

 Connect the 

Red

 and 

White

 RCA

jacks labeled “RSE/SYNC/SAT” to the audio AUX-IN jacks of the aftermarket radio.

• 

For models equipped without SYNC

®

:

 Connect the 

Red

 and 

White

 RCA jacks labeled 

“FROM 3.5” to the audio AUX-IN jacks of the aftermarket radio.

Continue to 3.5mm jack steering wheel control retention

From the 16-pin harness with stripped leads to the aftermarket radio:

•  Connect the 

Red

 wire to the accessory wire.

•  If equipped with a factory subwoofer, connect the 

Blue/White

 wire to the amp turn on wire.

•  If the aftermarket radio has an illumination wire, connect the 

Orange/White

 wire to it.

•  If the aftermarket radio has a mute wire, and the vehicle is equipped with SYNC

®

, connect

the 

Brown

 wire to it. If the mute wire is not connected, the radio will turn off when SYNC

®

is activated.

•  Connect the 

Gray

 wire to the right front positive speaker output.

•  Connect the 

Gray/Black

 wire to the right front negative speaker output.

•  Connect the 

White

 wire to the left front positive speaker output.

•  Connect the 

White/Black

 wire to the left front negative speaker output.

•  Tape off and disregard the following (4) wires, they will not be used in this application:

Green

Green/Black

Purple

Purple/Black

The following (3) wires are only for multimedia/navigation radios that require these wires.

•  Connect the 

Blue/Pink

 wire to the VSS/speed sense wire.

•  Connect the 

Green/Purple

 wire to the reverse wire.

•  Connect the 

Light Green

 wire to the parking brake wire.

Summary of Contents for 99-5834CH















Reviews: