background image

REV

. 1/26/2017   INST99-3307G

INSTALLATION INSTRUCTIONS FOR PART 99-3307G

METRA.  The World’s best kits.

®

metraonline.com

© COPYRIGHT 2017  METRA ELECTRONICS CORPORATION

 

CAUTION!

 

 All accessories, switches, climate controls panels, 

and especially air bag indicator lights must be connected before 
cycling the ignition. Also, do not remove the factory radio with 
the key in the on position, or while the vehicle is running.

 

• ISO DIN radio provision with pocket

• ISO DDIN radio provision

• 

Painted gray to match factory finish

• A) Radio trim panel • B) Radio brackets • C) Pocket • D) (6) #8 x 3/8” Phillips screws  

• E) (2) #10 x ¾” Phillips screws • F) (2) #10 panel clips • G) Axxess interface and wiring harness (not shown)

KIT FEATURES

KIT COMPONENTS

WIRING & ANTENNA CONNECTIONS

 (sold separately)

Wiring Harness: • Axxess interface and harness included
Antenna Adapter: • 40-EU55

• Panel removal tool • Phillips screwdriver  
• 9/32” socket wrench

TOOLS REQUIRED

Chevy Equinox 2010-2015 / GMC Terrain 2010-2014

(with monochrome display)

99-3307G

A

Table of Contents

B

C

E

F

D

Dash Disassembly

 ................................................. 2

Kit Preparation

 ....................................................... 3

Kit Assembly

 

ISO DIN radio provision with pocket ...................... 4

 

ISO DDIN radio provision ...................................... 4

Axxess Interface Installation

 .............................5-7

Summary of Contents for 99-3307G

















Reviews: