METAWOOD 5411074127695, Original Instructions Manual

Page: 30 / 43

2
WARNING:
• Never use the tool if the blade guard or spring
are damaged, faulty or removed. Operation of the
tool with a damaged, faulty or removed guard may
result in serious personal injury.
If the see-through blade guard becomes dirty, or
sawdust adheres to it in such a way that the blade
and/or workpiece is no longer easily visible, unplug
the saw and clean the guard carefully with a damp
cloth. Do not use solvents or any petroleum-based
cleaners on the plastic guard because this may
cause damage to the guard.
DO NOT DEFEAT OR REMOVE GUARD.
• It is extremely important to always secure the
workpiece correctly with the proper type of vise
or crown molding stoppers. Failure to do so may
result in serious personal injury and cause damage
to the tool and/or the workpiece.
• After a cutting operation do not raise the blade
until it has come to a complete stop. The raising
of a coasting blade may result in serious personal
injury and damage to the workpiece.
- Instruction to support long workpieces cut
• When cutting a workpiece that is longer than
the support base of the saw, the material should
be supported the entire length beyond the
support base and at the same height to keep the
material level. Proper workpiece support will help
avoid blade pinch and possible kickback which may
result in serious personal injury. Do not rely solely
on the vertical vise and/or horizontal vise to secure
the workpiece.
Thin material tends to sag. Support workpiece over
its entire length to avoid blade pinch and possible
KICKBACK.
The holders can be installed on either side as a
convenient means of holding workpieces
horizontally. Slip the holder rods into the holes in the
base and adjust their length according to the
workpiece to be held. Then tighten the holders
securely with the screws.
- Fixing the machine to a workbench.
The machine must be screwed to a workbench.
■ Mark the position of the mounting holes on the
workbench.
■ Drill holes at each of the marked positions,
adjusting the diameter and depth of the holes to the
screws used.
■ Place the machine on the workbench and insert
the screws into the mounting holes.
■ Firmly tighten the screws.
- Information to set the minimum size of the
pieces to be cut
Minimal workpiece sizes (= all workpieces that can
be clamped left or right from the saw blade with the
provided quick-action clamp
60 x 10 mm (length x width)
- Information on the maximum cross
section of a workpiece in a cross
Bevel
Miter angle
0° 45°
0° 60x120mm 60x80mm
45° 30x120mm 30x80mm
- The outer diameter ranges, the bore
diameter and the thickness of the blades
can be used
Blade Diameter 210 mm
Bore diameter
30 mm
Blade thickness 2.5/2.6 mm
- The maximum depth of cut
Cutting capacity, max. (0°/0°): 120x60 mm
WARNING: Packaging materials
are not toys! Children must not
play with plastic bags! Danger of
suffocation!
INTENDED USE
This tool is designed for cutting wood and plastic
that will fit in machine.
It is not suitable for cutting timber for fuel. Only use
saw blades that are suitable for machine and do not
use cutting discs.
The manufacture assumes no liability whatsoever
for improper use or if the machine has been
tampered with.
Give equal attention to safety instructions, assembly
and operating instructions as well as prevailing
accident preventions regulations.
The equipment is intended for use only in a power
supply which permissible modulus of system
impedance is 0.420
Ω or less
ADDITIONAL SAFETY RULES FOR
TOOL
1.
Wear eye protection.
2. Keep hands out of path of saw blade. Avoid
contact with any coasting blade. It can still
cause severe injury.
3. Do not operate saw without guards in place.
Check blade guard for proper closing before
each use. Do not operate saw if blade guard
does not move freely and close instantly.
Never clamp or tie the blade guard into the
open position.
4. Do not perform any operation freehand. The
workpiece must be secured firmly against the
turn base and guide fence with the vise during
all operations. Never use your hand to secure
the workpiece.
5. Never reach around saw blade.
6. Turn off tool and wait for saw blade to stop
before moving workpiece or changing settings.
7. Unplug tool before changing blade or
servicing.