background image

2    

7351J Very Intelligent Early Warning (VIEW) Laser Smoke Detector Technical Bulletin

Introduction

This document contains important information about installing,
maintaining, testing, and operating the Johnson Controls 7351J VIEW
laser detector. This detector is manufactured by System Sensor for use
with Johnson Controls fire alarm systems. If you install this detector for
someone else to use, leave a copy of this document with the user.

Before you install any 7351J VIEW laser detectors, read and become
familiar with the following:

 

the installation manual for the control panel system

 

the requirements of the Authority Having Jurisdiction (AHJ)

Select the publications that are relevant to this installation:

 

National Fire Protection Association (NFPA) 72 National Fire Alarm
Code

 

for non-United States installations, the applicable codes and standards
specific to the country and locality of installation

!

  CAUTION: Risk of Equipment Failure.

Failure to follow these directions may result in failure of this device to report an
alarm or trouble condition or respond properly to an alarm condition.
Johnson Controls is not responsible for devices that were improperly installed,
tested, or maintained by others.

As is the case with all installations under NFPA, Underwriter’s
Laboratories®, Inc. (UL), Underwriter’s Laboratories of Canada (ULC),
or Canadian Electrical Code classification, final written approval of
permissible operation and configuration rests with the Authority Having
Jurisdiction (AHJ).

Johnson Controls smoke detectors are marked with a compatibility
identifier—the last digit of the five-digit code stamped on the base of the
product. Connect detectors to compatible control units only. For a list of
UL-Listed control units and detectors, refer to the Johnson Controls

Device Compatibility Technical Bulletin (LIT-445180)

.

Prerequisites

Standards

Summary of Contents for 7351J














Reviews: