manualshive.com logo in svg

Metaphase Technologies DDC-3, User Manual

Share
Download
Metaphase Technologies DDC-3 User Manual Download Page 9

metaphase-tech.com

Metaphase

Technologies

DDC-3

pg. 9

DDC-3 Ethernet Command List

For users that do not want to use the MetaBOSS Software or the DDC-3 keypad, Metaphase provides 
an Ethernet command list that can be embedded into users’ custom programs.  Use the link below to ac-

cess the complete command list on Metaphase Technologies’ website, located in the “file cabinet” at the 

bottom of the page:

http://www.metaphase-tech.com/Controllers/Controllers/DDC_3

The Ethernet commands are of the following format:

 

 
 

Incoming and Outgoing Message Structure:

  

<2-byte length> <1-byte channel> <1-byte command> <1-byte reserved> <3-bytes of data>

 
  
 

Message Example:

  00 08 00 B3 00 00 00 31 

all data is in Hex (the space between bytes are added here just for readability 
and should not be included in the message) 

  
 

• Length is   

00 08   

the length is always 00 08

 
 

• Channel is   

00 

 

channel is either 00 or 01

 
 

• Command is 

B3 

 

command for setting output level

 
 

• Reserved is   

00 

 

reserved is always 00

 
 

• Data is  

 

00 00 31 

Output Level for channel 1 is 4.9V (31 hex is 49 decimal)

[APPENDIX B]

[APPENDIX B]

Summary of Contents for DDC-3












Reviews:

No comments

Brands by name

Popular brands

Load more brands