ENGLISH
32
The transport handles are installed on
the front legs of the saw.
1. To each transport handle
fit a
with
from the front.
2. Install transport handles in such
way that the tubes can be folded
down
.
3. From inside screw on one each
flange nut
Accessory holder installation
In the last installation stage, another
two screw hooks are screwed to the
front legs as supports for the push
stick, handle for push block and assem-
bly key.
1. Screw one flange nut
about
10 mm onto the two screw hooks
.
2. Put the screw hooks from the out-
side through the lateral bore of the
left front leg and secure with anoth-
er flange nut.
3. Fix the other screw hook to the right
front leg in the same manner.
7.1
Mains connection
B
Danger! High voltage
Operate saw in dry environment
only.
Operate saw only on a power source
matching the following requirements
(see also 'Technical Data'):
– Outlets properly installed,
earthed, and tested.
– three-phase outlets with neutral
wire installed;
– Mains voltage and system fre-
quency conform to the voltage
and frequency shown on the ma-
chine's rating label.
– Protection against electric shock
by a residual current device
(RCD) of 30 mA sensivity.
– Fuse protection of 16 A maximum
against short circuits.
– System impedance Zmax. at the
house service connection: see
separate supplement.
3
Note:
Contact your Electricity Board or a qua-
lified electrician if you are not sure if
your house service connection meets
these requirements.
Make sure that the mains cable is
out of the way so that it does not in-
terfere with the work and cannot be
damaged.
Protect mains cable from heat, ag-
gressive liquids and sharp edges.
Use only rubber-insulated extension
cables with sufficient cross sections
(see 'Technical Data').
Do not pull on mains cord to unplug.
B
Changing the direction of ro-
tation!
(only possible for version with DC
motor)
Depending on the wiring of the elec-
trical connection the saw blade may
rotate the wrong way.This can lead
to the workpiece being hurled away
when attempting to make a cut. The
direction of rotation must therefore
be checked every time the saw is
connected to another outlet. In case
of an incorrect direction of rotation,
the wiring of the outlet must be
changed by a qualified electrician:
1. After the saw and all of its safety
devices have been assembled, con-
nect it to the mains supply.
2. Raise saw blade fully.
3. Start saw and switch OFF immedi-
ately.
4. Check the saw blade's direction of
rotation from the left-hand side of
the saw. The saw blade must rotate
clockwise.
5. If the saw blade rotates anticlockwi-
se, unplug the power cable at the
saw.
6. Have the electric supply changed
by a qualified electrician!
7.2
Set-up
Place the machine on a firm, level
floor.
To align the table surface horizon-
tally, compensate for unevenness or
slippery floor surfaces using suitab-
le materials. Then check that the
machine is stable.
Ensure there is sufficient space to
handle larger workpieces.
For maximum upright stability the saw
can be bolted to the floor:
1. Place the fully assembled saw at a
suitable site and mark the bore ho-
les on the floor.
2. Move saw aside and drill the holes.
3. Align saw with the holes and bolt to
the floor.
A
Risk of injury!
This saw may only be operated by
one person at a time. Other persons
shall stay only at a distance to the
saw for the purpose of feeding or re-
moving stock.
Before starting work, check to see
that the following are in proper wor-
king order:
– mains cable and plug;
– ON/OFF switch;
– riving knife;
Item Description
Qty.
Flange nut M6
4
Screw hooks
M6 x 50
2
125
126
127
128
129
130
8.
Operation
