ENGLISH
18
This section describes problems and
malfunctions which you should be able
to resolve yourself. If the measures de-
scribed here do not solve your problem,
see 'Repairs'.
A
Danger!
Many accidents happen particularly in
connection with problems and faults.
Therefore please note the following:
Always unplug before troubleshooting.
Check that all safety devices are oper-
ational again after each fault service.
No crosscut function
Transport locking pin engaged:
Pull transport locking pin out.
Safety lock engaged:
Release safety lock.
Sawing performance too low
Saw blade blunt (possibly tempering
marks on blade body):
Saw blade not suitable for material be-
ing cut (see section 'Technical Data');
Saw blade warped:
Replace saw blade (see section
'Maintenance').
Saw vibrates heavily
Saw blade warped:
Replace saw blade (see section
'Maintenance').
Saw blade incorrectly mounted:
Remove the saw blade and then
mount it again correctly (see chapter
'Care and Maintenance').
Rotary table stiff
Sawdust build-up under rotary table:
Remove saw dust.
14. Trouble Shooting
15. Technical Data
KGS 216 M
KGS 254 M
Voltage
V
230 – 240 (1~ 50/60 Hz) 230 – 240 (1~ 50/60 Hz)
Current draw
A
7
8,7
Fuse protection
A
10 (time-lag)
10 (time-lag)
Motor capacity (S6 20% 5 min.)
kW 1.5
1.8
Protection rating
IP
20
20
Protection class
II
II
Saw blade speed
min
-1
5000
4500
Cutting speed
m/s
55
55
Saw blade diameter (outer)
mm
216
254
Arbor bore
mm
30
30
Dimensions
Machine in packaging (length × width × height)
Machine ready for operation, rotating table in 90° position
(length / width / height)
mm
mm
895 × 475 × 380
820 × 543 × 355
895 × 545 × 420
850 × 620 × 400
Maximum workpiece cross section:
Standard cross cuts
- Turntable 0°, rocker arm 0°
Mitre cuts
- Turntable 15° / rocker arm 0°
- Turntable 22,5° / rocker arm 0°
- Turntable 30° / rocker arm 0°
- Turntable 45° / rocker arm 0°
Bevel cuts
- Turntable 0°, rocker arm 45°
Compound mitre cuts
- Turntable 15° / rocker arm 45°
- Turntable 22,5° / rocker arm 45°
- Turntable 30° / rocker arm 45°
- Turntable 45° / rocker arm 45°
mm
mm
mm
mm
mm
mm
mm
mm
mm
mm
width / height
305 / 65
295 / 65
280 / 65
260 / 65
215 / 65
305 / 36
295 / 36
280 / 36
260 / 36
215 / 36
width / height
305 / 90
295 / 90
280 / 90
260 / 90
215 / 90
305 / 47
295 / 47
280 / 47
260 / 47
215 / 47
Weight
Machine in packing
Machine ready to work
kg
kg
19
14
23
17,5
Permissible temperature for transport and storage
°C
0 to +40
0 to +40
Noise emission according to EN 61029-1
Sound power level L
WA
Sound pressure level at operator's ear L
PA
Uncertainty K
dB(A)
dB (A)
dB (A)
86.8
99,8
3,0
86.8
99,8
3,0
Effective value of weighted acceleration according to EN 61029-1
(Vibration on handle) Vector sum a
h
Uncertainty K
m/s
2
m/s
2
< 2.5
1.5
< 2.5
1.5
Dust collector (not included in standard delivery):
Diameter of dust extraction port at rear of saw
Minimum air volume flow
Minimum vacuum at suction port
Minimum air speed at suction port
mm
m
3
/h
Pa
m/s
31.6
460
530
20
31.6
460
530
20
Laser guide:
Laser product class
Laser product standard
Max. output power P
Wave length
mW
nm
2
EN 60825-1: 1994 +A1 +A2
1.0
650
2
EN 60825-1: 1994 +A1 +A2
1.0
650
* The values stated are emission values and as such do not necessarily constitute values which are safe for the workplace. Although there is a correlation between emis-
sion levels and environmental impact levels, whether further precautions are necessary cannot be derived from this. Factors influencing the actually present environmen-
tal impact level in the workplace include the characteristics of the work area and other noise sources, i.e. the number of machines and other neighbouring work proc-
esses. The permitted workplace values can likewise vary from country to country. This information is intended to assist the user in his estimate of hazards and risks.
