11
ENGLISH
en
rotating accessory may grab the surface and pull
the power tool out of your control.
m)
Do not run the power tool while carrying it
at your side.
Accidental contact with a rotating
accessory could snag your clothing, pulling the
accessory into your body.
n)
Regularly clean the power tool’s air vents.
The motor’s fan will draw the dust inside the
housing and an excessive accumulation of
powdered metal may cause electrical hazards.
o)
Do not operate the power tool near
flammable
materials. Sparks could ignite these
materials.
p)
Do not use accessories that require liquid
coolants.
Using water or other liquid coolants may
result in electrocution or shock.
4.2
Kickback and Related Warnings
Kickback is a sudden reaction to a pinched or
snagged grinding wheel, backing pad, brush or
any other accessory. Pinching or snagging causes
rapid stalling of the rotating accessory. This in turn
causes the uncontrolled power tool to be forced in
the opposite direction from which the accessory is
rotating at the pinched or snagged point.
For example, if an abrasive wheel is snagged or
pinched by the workpiece, the edge of the wheel
entering the pinch point can dig into the surface of
the material causing the wheel to climb out or kick
out. The abrasive wheel may either jump toward or
away from the operator, depending on direction the
disc is moving at the pinch point. Abrasive wheels
may also break under these conditions.
Kickback is the result of power tool misuse and/or
incorrect operating procedures or conditions and
can be avoided if suitable precautionary measures
are taken as described below.
a)
Maintain a firm grip on the power tool and
position your body and arm so that you can
resist kickback forces. Always use the
auxiliary handle, if provided, for maximum
control over kickback or torque reaction
during start-up.
The operator can control torque
reactions or kickback forces, if proper precautions
are taken.
b)
Never place your hand near a rotating
accessory.
The accessory may kickback over your
hand.
c)
Do not position your body in the area where
the power tool will move if kickback occurs.
Kickback will propel the tool in the direction
opposite to the grinding wheel’s movement at the
pinch or snag point.
d)
Use special care when working corners,
sharp edges etc. Avoid bouncing and
snagging the accessory.
Corners, sharp edges
or bouncing have a tendency to snag the rotating
accessory and cause loss of control or kickback.
e)
Do not attach a saw chain, woodcarving
blade or toothed saw blade.
Such blades create
frequent kickback and can cause you to lose
control.
4.3 Safety Warnings Specific for Grinding
and Cut-Off Grinding:
a)
Use only wheel types that are recommended
for your power tool and the specific guard
designed for the selected wheel.
Wheels for
which the power tool was not designed cannot be
adequately guarded and are unsafe.
b)
The grinding surface of the centre
depressed wheels must be mounted below the
plane of the guard lip.
An improperly mounted
grinding wheel that projects through the plane of
the guard lip cannot be adequately guarded.
c)
The guard must be securely attached to the
power tool and positioned for maximum safety
so that the least amount of wheel is exposed
towards the operator.
The guard helps to protect
operator from broken wheel fragments and
accidental contact with the wheel and sparks
which could ignite clothing.
d)
Grinding media must be used only for
recommended applications.
For example: do not grind with the side of the
cutting disc.
Cutting discs are intended for
grinding using the edge of the disc. Applying force
to the sides of these discs may cause them to
shatter.
e)
Always use undamaged wheel flanges that
are the correct size and shape for your
selected grinding wheel.
Proper wheel flanges
support the grinding wheel, reducing the possibility
of breakage. Flanges for cutting discs may be
different from grinding wheel flanges.
f)
Do not use worn down grinding wheels from
larger power tools.
Grinding wheels intended for
larger power tools are not suitable for the higher
speed of a smaller tool and may break.
4.4 Additional Safety Warnings Specific for
Cut-Off Grinding:
a)
Do not “jam” the cutting disc or apply
excessive pressure. Do not attempt to make an
excessively deep cut.
Overstressing the cutting
disc increases the load and makes the disc more
susceptible to twisting or bending in the cut and
more likely to kick back and break.
b)
Do not position your body in line with or
behind the rotating cutting disc.
When the cutting
disc is moving away from your body at the point of
operation, any kickback can propel the spinning disc
and the power tool directly towards you.
c)
If the cutting disc is stuck or when
interrupting a cut for any reason, switch off
the power tool and hold the power tool
motionless until the disc comes to a complete
stop. Never attempt to remove the cutting disc
from the cut while the disc is in motion;
otherwise kickback may occur.
Investigate and
take corrective action to eliminate the cause if a
disc becomes stuck.
d)
Do not restart the cutting operation in the
workpiece. Let the cutting disc reach full
speed and carefully re-enter the cut.
The wheel
may bind, walk up or kickback if the power tool is
restarted in the workpiece.
