5
Section 4: Installation
4.1 Installation Precautions
To ensure that the installation is performed correctly
carefully follow the instructions indicated in this manual.
Failure to follow instructions indicated not only can cause
malfunctions of the appliance but also void the warranty.
It is important that the electrical installation is made in
accordance with local codes, respects the data indicated
in the technical sheet and is correctly earthed.
The appliance must be installed in a position that allows
for routine maintenance, such as filter cleaning.
The system inlet water temperature must not exceed
160°F. Failure to comply can severly damage the unit and
will void the warranty.
4.2 Positioning the Unit
Avoid installing the unit in close proximity to:
-positions subject to exposure of direct sunlight
-in proximity to sources of heat
-in damp areas or places with probable contact with water
-in places with oil fumes
-places subject to high frequencies
Make sure that:
-the wall on which the unit is to be installed on is strong
enough to support the weight
-the part of the wall being used does not have pipes or
electric wires passing through
-is free of obstacles which could interfere with the inlet
and outlet air flow
-is preferably an outside perimeter wall to allow the
discharge of condensation outside.
4.3 Minimum Clearances
Figure 5 indicates the minimum mounting distances be-
tween the wall-mounted cooler-convector and furniture
present in the room.
Figure 5
0. 79 inch
0. 79 inch
3. 54 inch
15 .7 5inch
5. 51 inch
A
B
C
E
Removal of Side Panel (Fig. 6)
Dismount the upper grill (Fig. 6 Ref. A) by unscrewing the
fixing screws.
Lift the cover (Fig. 6 Ref. B) that protects the screw (Fig.
6 Ref. C) and unscrew it. Move the side panel slightly and
lift it out.
Figure 6
Wall installation or vertical floor
Using the paper template, trace the position of the wall
(Fig. 7). Use a suitable drill to make the holes with and
insert the toggle bolts (2 for each bracket) (Fig. 8 Ref. A);
affix the two brackets (Fig. 8 Ref. B).
Figure 7
Figure 8
P F P te
mpla te
code:
20000
-23030
9
P a ra lle
l to the
floor
L evel
check
line
165mm
90
L evel
check
line
165mm
025
040
060
080
100
0
200
400
600
800
90
025
040
060
080
100
0
200
400
600
800
2-
8 L oca
te hole
Make sur
e tha t th
e space b
e tween
two tem
plates
is accord
ing to th
e table re
qu ireme
nt when
installing
PFP 025
to 100.
The dis
tance fr
om the
center o
f
locate
hole to
the top
edge o
f
machin
e is 165
mm
The dis
tance fr
om the
center o
f
locate
hole to
the top
edge o
f
machin
e is 165
mm
2-
8 L oca
te hole
Make su
re tha t
the spac
e be twe
en two t
emplate
s
is accord
ing to th
e table r
equ irem
ent whe
n
installin
g PFP 0
25 to 10
0.
Water i
nlet ho
le
withou
t electr
otherm
al 3-wa
y valve
Water i
nlet ho
le
Water o
utlet ho
le
Conden
sation d
rain ho
le
The dis
tance b
etween
two tem
plates(
mm)
The dis
tance b
etween
two tem
plates(
mm)
Model
Model
The bo
ttom o
f mach
ine
The bo
ttom o
f mach
ine
Fold 90
degree
along
this lin
e
Fold 90
degree
along
this lin
e
R e s e r
ve d a r
e a for
wa te r
pipe h
ole
P a ra lle
l to the
floor
A
B
