background image

13

SAFETY FIRST!

Whilst Merlin have engineered safety features into your garage door opener, we urge you to consider fitting The Protector

System

(IR Beams) to your new garage door opener. In many countries these devices are compulsory to assist in preventing

serious injury or property damage. For your own peace of mind and the safety of others please install this inexpensive safety

device.

NOTE: This accessory must be used for all installations

where the closing force as measured on the bottom of the

door is over 400 N (40 kgf).

S

PECIAL NOTE: Merlin strongly recommends that The

Protector System

TM

be installed on all garage door

openers.

IR BEAMS:

By installing IR Beams, an open door is prevented

from closing if a person or object is located in the beam area. If

the door is already closing, it will return to the open position. A

closed door is not prevented from opening.
If the Protector System

TM

is installed and needs to be removed,

the opener will need to be reprogrammed (refer to paragraph 4

of the troubleshooting section).

THE PROTECTOR SYSTEM

TM

(OPTIONAL)

T

o prevent entrapment, install The Protector

System™ no higher than 100 mm above the floor.

Disconnect power to the garage door opener

before installing The Protector System™.

21

22

PROGRAM TRANSMITTERS TO THE OPENER LIGHT

To Program your transmitters to operate your garage door opener light follow the below steps:

1.Press and release the “LEARN” button, and the “courtesy light” will flash twice (fig.1).

2.Press and release the “PROG” button and the garage door opener will go into

Courtesy Light learn mode for 30 seconds (fig.2).

3.Press any transmitter button (fig.3) to learn this button to the garage door opener

courtesy Light, the garage door opener "courtesy Light" will flash twice.

NOTE: Do not use the same transmitter button that has been previously

learned to the garage door opener for operation.

The transmitter is now learnt to the garage door opener courtesy Light.

To Erase all Remote Control Codes

1.Press and hold the “LEARN” button on the opener until the courtesy light flashes

twice, and continue holding for approximately 8 seconds, until the courtesy light

flashes twice again.

2.Release the button, all codes are now erased.

fig.3

fig.1

fig.2

Indicator LED

Indicator LED

Summary of Contents for MS65MYQ

























Reviews: