manualshive.com logo in svg

Merits p314 series, Service Manual, Page: 3 / 15

Share
Download
Merits p314 series Service Manual Download Page 3

1

1. Introduction

The purpose of this manual is to provide dealers and/or distributors with
the product information and instructions that are required for servicing the
P314 powerchair.

2. Service guide

The P314 powerchair consists of three main parts:

n

Seat assembly

n

Body assembly

n

Electrical system (Please refer to P3/P7 series Shark or VR2 service
manual)

2.1. How to replace or repair the seat assembly

The Seat assembly includes the seat body, the seat mounting, the seat
hook, the trapeze bar upright weldment (front) assembly, the seat
tower (rear) assembly, the seat mount connector assembly and the
left/right armrest.

2.1.1. To replace the seat body

◆

When should you replace the seat body?

◇

If the seat body is worn out.

◇

If the seat body is pierced or scratched by something.

◇

 If the powerchair crashed cause the seat body out of shape.

◆

How to replace the seat body?

◇

Please proceeding steps as follows if it has to replace.

Replace the seat body by the following steps if it is broken.

a.

 Use hex tools to loosen hex fixed bolt (3.10) on the hook (3.09)

and remove it from the seat body.

b.

 Use hex tools to loosen hex fixed bolt (3.08) on the seat

Summary of Contents for p314 series
















Reviews:

No comments