manualshive.com logo in svg

Meritor MM-0861, Maintenance Manual

Share
Download
Meritor MM-0861 Maintenance Manual Download Page 89

Copyright Meritor, Inc., 2022

MM-0861  /  Revised 06-22

Page 87

Printed in USA

8     Power Takeoff (PTO)

SEAL

SPRING

CAP

4000226a

Figure 8.12 

n. Apply a thin film of Loctite

®

 518 gasket material to the cap 

surface. Install the cap with the 1/4-20 screws using Loctite

®

 

242 sealant. Tighten the screws to 10-14 lb-ft (14-19 Nm). 
Figure 8.12. 

o. Install the PTO shaft seal into the housing.
p. Press the seal into position until the seal is seated on the 

housing.

3.  Install the PTO assembly onto the transfer case.

4.  Apply a thin film of Loctite

®

 518 gasket material to the 

housing.

5.  Slide the housing onto the output shaft of the transfer case, 

aligning the splines of the clutch to the shaft.

6.  Install the eight 7/16” (11 mm) diameter screws and washers 

using Loctite

®

 277 sealant. Tighten the screws to 60-75 lb-ft 

(81-102 Nm). 

7.  Verify the clutch engages and disengages correctly.

8.  Pressure test the PTO shifter for air leakage by performing the 

following steps.

a. With the correct fitting installed into the air control port, apply 

a pressure of 90 psi (6.2 bar).

b. Shut off the air supply.

 CAUTION

Check for external leaks at the cover plate joint and fitting if the 
pressure decreases more than 5 psi (0.3 bar) in 10 minutes. 
Leaks can cause component damage.

c. Check for external leaks at the cover plate joint and fitting 

if the pressure decreases more than 5 psi (0.3 bar) in 10 
minutes. 

 

If the external joints are sealed and the leakage is still 
more than 5 psi (0.3 bar):

 Remove the piston and inspect 

the o-ring and housing bore for damage. Repair parts as 
necessary.

9.  Install the indicator switch. Tighten the switch to 25-30 lb-ft 

(34-40 Nm). Figure 8.13.  

 

If a switch is not used: 

 

Install the special plug and washer used to cap the access 
hole. Tighten the plug to 25-30 lb-ft (34-40 Nm). Figure 8.13. 

4000227a

SPECIAL

PLUG AND

WASHER

AIR CONTROL

PORT

OPTIONAL

CONNECTOR

SWITCH

ASSEMBLY

INDICATOR

SWITCH

Figure 8.13 

10.  Repeat Step 1 through Step 9 for each remaining declutch, 

PTO or proportional differential lockout assemblies.

Summary of Contents for MM-0861























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands