manualshive.com logo in svg

Meridian DSP5200, User Manual, Page: 68 / 73

Share
Download
Meridian DSP5200 User Manual Download Page 68

TROUBLESHOOTING

61

Drive units move when the speaker is switched on or 
off

This is normal as the speaker active electronics settle.

Confi guring the DSP loudspeaker does not have any 
effect

Make sure that you are confi guring the DSP loudspeaker used as the 

master digital loudspeaker in the system. This determines the confi guration 

of all digital loudspeakers in the system.

Unit stays in standby

•

 Check that it is connected correctly.

•

 Turn the system on from another Meridian product in the system.

Only the master loudspeaker plays

•

 Check the S5 cables are connected correctly.

Sound is odd or mono

•

 Check that the DSP loudspeakers are correctly confi gured as Left and 

Right respectively.

The green indicator fl ashes or stays on

This indicates that DSP clipping is occurring.

Brief fl ashes indicate occasional clipping which will not be audible.

If the indicator stays on for long periods this may indicate a fault in the 

confi guration of your system, and you should contact your Meridian dealer.

Summary of Contents for DSP5200










































































Reviews:

No comments