background image

Section 2 - Getting to Know Your Power Package 

Page  22

90-8M0050539   

eng

  MAY  2011

Additional Operation Instructions for Axius Systems

If your boat has DTS engines equipped with an Axius system, refer also to the 

Axius Operation Manual

 included with the boat.

Identification

The serial numbers are the manufacture's keys to numerous engineering details which apply to your MerCruiser power package.

When contacting MerCruiser about service, always specify model and serial numbers.

Engine Serial Number Decal MPI

The serial number decal is located on the engine cover.

25903

Serial numbers and maintenance color codes decal

The engine serial number is also stamped in the engine block.

Alpha Sterndrive Decal Identification

The Drive Serial No. is located on the port side of the alpha sterndrive.
The Drive Ratio is located on the starboard side of the alpha sterndrive.

Alpha sterndrive

a -

Drive gear ratio decal (starboard)

b -

Serial number decal (port)

b

a

25681

Summary of Contents for MerCruiser Axius SeaCore 350 MAG











































































































































































Reviews: