manualshive.com logo in svg

Mercury 2009 Grand Marquis, Owner'S Manual

Share
Download
Mercury 2009 Grand Marquis Owner'S Manual Download Page 48

Replacing headlamp bulbs

To remove the headlamp bulb:

1. Make sure the headlamp control is in the off position, then open the
hood.

2. Remove the three pin type retainers and the radiator sight shield.

3. Remove the front parking lamp assembly. Refer to

Replacing front

parking/cornering/turn signal lamp bulbs

in this section.

4. Remove the headlamp retainer
bolts and the headlamp assembly.

5. Disconnect the electrical
connector.

6. Remove the old headlamp bulb by
rotating it counterclockwise and pull
it out.

7. To install, reverse the removal
procedure. (Re-aiming the headlamps
may be necessary. For additional
information, refer to the headlamp
aiming section in this chapter.)

WARNING:

Handle a halogen headlamp bulb carefully and keep

out of children’s reach. Grasp the bulb only by its plastic base

and do not touch the glass. The oil from your hand could cause the
bulb to break the next time the headlamps are operated.

Note:

If the bulb is accidentally touched, it should be cleaned with

rubbing alcohol before being used.

Note:

The headlamp bulb should not be removed from the headlamp

until just before a replacement bulb is installed. Removing the bulb for
an extended period of time may affect headlamp bulb performance.
Contaminants may enter the headlamp where they can settle on the lens
and reflector. Never turn the headlamps on with the bulb removed.

2009 Grand Marquis

(grn)

Owners Guide

(own2002)

, 2nd Printing

USA

(fus)

Lights

48

Summary of Contents for 2009 Grand Marquis















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands