MerCruiser QSD 2.0 Manual Download Page 74 | Manualshive

Page: 74 / 135

background image

Section 5 - Maintenance

Page 66

90-8M0057081

eng

MARCH 2011

b. Inspect the gasket in the pressure cap for damage and replace if necessary.

a -

Gasket

c. The pressure cap maintains pressure on the cooling system and may not be holding pressure properly. To have the cap

tested, contact your Cummins MerCruiser Diesel Authorized Repair Facility.

d. Add the specified coolant as necessary. See

Filling

.

IMPORTANT: When installing the pressure cap, be sure to tighten it securely to prevent coolant loss.

5. If the coolant level is correct, install the pressure cap and tighten securely.
6. Recheck the coolant level after the first WOT boat test and add coolant, if necessary.

Filling

1. Allow the engine to cool.
2. Remove the pressure cap from the coolant expansion tank.
3. If the coolant is low in the coolant expansion tank, add the specified coolant as necessary to bring the level to within 25 mm

(1 in.) of the bottom of the fill neck.

Engine coolant fill location

(engine cover removed)

a -

Coolant cap

b -

Coolant expansion tank

c -

Bottom of fill neck

Description

Where Used

Part Number

Marine Engine Coolant

Closed cooling system

92‑813054A2

Europe Only

Fleetguard Compleat with DCA4

Fleetguard Part Number: CC2825

Obtain Locally

IMPORTANT: When installing the pressure cap, be sure to tighten it securely to prevent coolant loss.

4. Install the pressure cap. Tighten securely.

Changing

Change (replace) the engine coolant at the prescribed interval. See

Replacing the Engine Coolant in the Closed Cooling

System

.

14142

a

a

b

c

25356

«
...
72
73
74
75
76
...
»

Summary of Contents for QSD 2.0








































































































































Reviews:

No comments

Related manuals for QSD 2.0

Brand: Wartsila Pages: 168

Brand: Danfoss Pages: 28

Brand: Yanmar Pages: 224

Brand: Danfoss Pages: 77

Brand: Thermador Pages: 20

Brand: ZAFFER Pages: 28

Brand: YARDMAX Pages: 25

Brand: SunStar Pages: 86

Brand: MTU Pages: 153

12 V 4000 T95 x

Brand: MTU Pages: 222

Brand: Dietz Pages: 10

Brand: Dietz Pages: 11

RolloTube S-line Sun DuoFern

Brand: RADEMACHER Pages: 2

Brand: O.S. engine Pages: 16

Brand: O.S. engine Pages: 46

Brand: Hotsy Pages: 68

Brand: Desert Aircraft Pages: 9

Brand: Jabiru Pages: 49

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands