MerCruiser QSD 2.0 Manual Download Page 105

Page: 105 / 135

Section 5 - Maintenance

90-8M0057081

eng

MARCH 2011

Page 97

Transom Assembly

1. Lubricate the gimbal bearing by applying approximately 8‑10 pumps of grease from a typical hand‑operated grease gun.

a -

Gimbal bearing grease insert

Tube Ref No.

Description

Where Used

Part No.

U-joint and Gimbal

Bearing Grease

Gimbal bearing grease insert

92-802870A1

Engine Coupler

IMPORTANT: These engines are equipped with a sealed engine coupler. The sealed coupler and the shaft splines can be

lubricated without removing the sterndrive.
1. Lubricate the engine coupler splines through the grease fitting on the coupler by applying approximately 8‑10 pumps of Engine

Coupler Spline Grease from a typical hand‑operated grease gun.

NOTE: If the boat is operated at idle for prolonged periods of time, the coupler should be lubricated on Bravo models every

50 hours.

a -

Grease fitting

b -

Coupler splines

Tube Ref No.

Description

Where Used

Part No.

Engine Coupler Spline

Grease

Engine coupler and shaft splines

92-802869A 1

Driveshaft Extension Models

1. Lubricate the transom end grease fitting and engine end grease fitting by applying approximately 10 ‑ 12 pumps of grease

from a typical hand‑operated grease gun.

19979

23500

Summary of Contents for QSD 2.0








































































































































Search results

Summary of Contents for QSD 2.0

Reviews:

Related manuals for QSD 2.0

Brands by name

Popular brands

MerCruiser QSD 2.0, Manual

Search results

Summary of Contents for QSD 2.0

Reviews:

Related manuals for QSD 2.0

Brands by name

Popular brands