MerCruiser QSD 2.0 Manual Download Page 102

Page: 102 / 135

Section 5 - Maintenance

Page 94

90-8M0057081

eng

MARCH 2011

•

Avoid any electrical interconnection between the paint and the Mercury MerCruiser product, anodic blocks, or

MerCathode system by allowing a minimum of 40 mm (1‑1/2 in.) unpainted area on the transom of the boat around these

items.

a -

Painted boat transom

b -

Unpainted Area on Transom

Painting the sterndrive unit or transom assembly

: The sterndrive unit and transom assembly should be painted with a

good‑quality marine paint or an anti‑fouling paint that does not contain copper, tin, or any other material that could conduct

electrical current. Do not paint drain holes, anodes, MerCathode system, or items specified by the boat manufacturer.

Lubrication

Steering System

WARNING

Incorrect cable lubrication can cause hydraulic lock, leading to serious injury or death from loss of boat control. Completely

retract the end of the steering cable before applying lubricant.

NOTE: If the steering cable does not have a grease fitting, the inner wire of the cable cannot be greased.

If the steering cable has grease fittings

, turn the steering wheel until the steering cable is fully retracted into the cable

housing. Apply approximately three pumps of grease from a typical hand‑operated grease gun.

a -

Steering cable grease fitting

Tube Ref No.

Description

Where Used

Part No.

Special Lubricant 101

Steering cable grease fitting

92-802865Q02

5578

6221

Summary of Contents for QSD 2.0








































































































































Search results

Summary of Contents for QSD 2.0

Reviews:

Related manuals for QSD 2.0

Brands by name

Popular brands

MerCruiser QSD 2.0, Manual

Search results

Summary of Contents for QSD 2.0

Reviews:

Related manuals for QSD 2.0

Brands by name

Popular brands