background image

 

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. 
This equipment should be installed and operated with minimum distance 20 cm between the radiator 
and your body. This transmitter must not be co-located or operating in conjunction with any other 
antenna or transmitter. 
 

FCC Professional Installation Statement

 

 

This equipment requires professional installation.  
 

Industry Canada Statement

 

 

The MG21-HW-NA, MG21E-HW-NA comply with license-exempt RSSs of the Industry Canada Rules. 
Operation is subject to the  following two conditions: (1) This device may not cause harmful interference, 
and (2) this device must  accept any interference received, including interference that may cause 
undesired operation. 
 
Ce dispositif est conforme à la norme RSS d

’I

ndustrie Canada applicable aux appareils radio exempts de 

licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire 
de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage 
susceptible de provoquer un fonctionnement indésirable. 
 
This radio transmitter has been approved by Innovation, Science and Economic Development Canada to 
operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna 
types not included in this list that have a gain greater than the maximum gain indicated for any type 
listed are strictly prohibited for use with this device. 
 
Antenna types: 
Dipole, Panel  
Antenna gain (in dBi):  

 

 
 
Innovation, Sciences et Développement économique Canada a approuvé l'utilisation de ce 
transmetteur  radio avec les types d'antenne énumérés ci-dessous, le gain maximal admissible étant 
indiqué. Les types  d'antennes non inclus dans cette liste qui ont un gain supérieur au gain maximal 
indiqué pour tout type  listé sont strictement interdits pour une utilisation avec cet appareil. 

Summary of Contents for MG21












Reviews: