Mendota FV46 Installation And Operating Instructions Manual Download Page 1

85-03-01108-J 

FV46 

 

Installation and Operating Instructions 

MODEL NO. AA-11-03763 FV46 FULLVIEW DIRECT VENT GAS FIREPLACE HEATER 

 

WARNING:

 If the information in these instructions is not 

followed exactly, a fire or explosion may result causing 

property damage, personal injury or loss of life. 

 

AVERTISSEMENT

. Assurez-vous de bien suivre les instructions 

données dans cette notice pour réduire au minimum le risque 

d'incendie ou d'explosion ou pour éviter tout dommage 

matériel, toute blessure ou la mort. 

- Do not store or use gasoline or other flammable 

vapors and liquids in the vicinity of this or any other 

appliance. 
- WHAT TO DO IF YOU SMELL GAS 

Do not try to light any appliance. 

Do not touch any electrical switch; do not 

use any phone in your building. 

Immediately call your gas supplier from a 

neighbor’s phone. Follow the gas supplier’s 

instructions. 

If you cannot reach your gas supplier, call 

the fire department. 

- Installation and service must be performed by a 

qualified installer, service agency or the gas 

supplier. 

Ne pas entreposer ni utiliser d'essence ni d'autres vapeurs 

ou liquids inflammables dans le voisinage de cet appareil 

ou de tout autre appareil.  
- QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:  

• Ne pas tenter d'allumer d'appareil. 

 

• Ne touchez à aucun interrupteur. Ne pas vous servir des 

téléphones se trouvant dans le bâtiment où vous trouvez.  

• Appelez immédiatement votre 

fournisseur de gaz depuis 

un voisin. Suivez les instructions du fournisseur.  

• Si vous ne pouvez rejoindre le fournisseur de gaz, 

appelez le service des incendies.  
- L'installation et l'entretien doivent être assurés par un 

installateur ou un service d'entretien qualifié ou par le 

fournisseur de gaz.  

This appliance may be installed in an aftermarket, 

permanently located, manufactured home (USA 

only) or mobile home, where not prohibited by local 

codes. 
This appliance is only for use with the type of gas 

indicated on the rating plate. This appliance is not 

convertible for use with other gasses, unless a 

certified kit is used. 

 Cet appareil peut être installé dans une maison 

préfabriquée (É.-

U. seulement) ou mobile déjà installée à 

demeure si les règlements locaux le permettent.  
Cet appareil doit être utilisé uniquement avec les types de 

gaz indiqués sur la plaque signalétique. Une trousse de 

conversion est fournie avec cet appareil. 

A barrier designed to reduce the risk of burns from 

the hot viewing glass is provided with this appliance 

and must be installed. 

 Une barrière conçue pour réduire le risque de brûlures 

du verre chaud est fournie avec cet appareil et doit être 

installée. 

Summary of Contents for FV46

































































































Reviews: