Mendota DXV-35 DT4 Installation & Operating Instructions Manual Download Page 1

MENDOTA GAS DIRECT VENT FIREPLACE  

with 

Premium Texture Fiber Logs Combustion System 

Model DXV-35 DT4 - LX 

INSTALLATION & OPERATING INSTRUCTIONS 

 

DXV35DT4-LX 0915 

 

WARNING 

If you do not follow these instructions exactly, a fire or 
explosion may result causing property damage, personal 
injury or loss of life. 

CAUTION: Keep gasoline and other liquids having flammable 
vapors away. 

 

WHAT TO DO IF YOU SMELL GAS 

 

Do not try to light any appliance. 

 

Do not touch any electrical switch; do not use any 
phone in your building. 

 

Immediately call your gas supplier from a neighbor's 
phone.  Follow the gas supplier’s instructions. 

 

If you cannot reach your gas supplier, call the fire 
department. 

WARNING 

Do NOT use this appliance if any part has been under water.  
Immediately call a qualified service technician to inspect the 
appliance and to replace any part of the control system and 
any gas control, which has been under water.

 

AVERTISSEMENT. Quiconque ne respecte pas à la lettre 
les instructions dans la présente notice risque de dé-
clencher un incendie ou une explosion entraînant des 
dommages, des blessures ou la mort.

 

ATTENTION. Garder l’essence ou autres liquides produi-
sant des vapeurs inflammables loin del’appareil.  

 

QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ : 

 

Ne pas tenter d’allumer d’appareil.  

 

Ne touchez à aucun interrupteur; ne pas vous servir 
des téléphones se trouvant dans le bâtiment. 

 

Appelez immédiatement votre fournisseur de gaz 
depuis un voisin. Suivez les instructions du 
fournisseur. 

 

Si vous ne pouvez rejoindre le fournisseur, appelez 
le service des incendies. 

N’utilisez pas cet appareil s’il a été plongé dans l’eau, 
même partiellement. Faites inspecter l’appareil par un 
technicien qualifiéet remplacez toute partie du système 
de contrôle et toute commande qui ont été plongés dans 
l’eau.

 

AVERTISSEMENT : 

Une installation, un réglage, une modifi-

cation, une réparation ou un entretien mal effectué peut cau-
ser des dommages matériels ou des blessures. Voir la notice 
de l'utilisateur quiaccompgne l’appareil. Pour de l’aide oueds 
renseignements supplémentaires, consultez un installateur, 
un technicien agréé ou le fournisseur de gaz.

 

WARNING

:  Improper installation, adjustment, alteration, 

service or maintenance can cause injury or property damage.  
Refer to this manual.  For assistance or additional information 
consult a qualified installer, service agency or the gas suppli-
er. 

Summary of Contents for DXV-35 DT4































































Reviews: