HARDWARE COMPONENTS
DESCRIPTION/PART
NO.
1) Grate Kit
VG4409
2) Savorizer
®
VG4403
3) Direct Flame
Insert
VG4407
4) Genie Tool
VG1594
5) Shelf Bolt
DS2311
6) Antenna
VG9025
7) #10 Screw
DS2185
8) Cord Wrap
VG0560
9) Power Cord
VG0911
10) Meat Probe
VG0956
QTY:
PICTURE
@
10
©
)
Q
�
2
Packaging Locations
Savorizer
®
Left Shelf
Right Shelf
z:
MEMPHIS PRO ASSEMBLY INSTRUCTIONS
1: Remove both shelves, the hardware kit, Savorizer
®
, and grate kit from the grill.
The controller shelf will be in the grill hood underneath the grate kit and
Savorizer
®
. To do so, cut the four zip ties holding the Savorizer
®
in place.
Remove all laser film on the grill. This is a peel-able plastic left on to
protect your grill from scratches during manufacturing and transit.
Remove all laser film and laser etch lines with the included stainless
steel wipes, WD40, or olive oil. Once a grill has been heated up it is
very difficult to remove this film, be sure to check your grill thoroughly
before first burn.
2: Replace the Savorizer
®
and place the four small grates on the lower level and
the long grate on the upper level.
3: Remove the Direct Flame Insert, Genie Tool, and included pellets from the
non-controller side shelf (right).
4: Remove the shelf pan and pan tray from the controller side shelf (left) before
installation.
5: Install the outer top two shelf bolts (#5) into the right side of the grill. Leave
approximately 1/4" of the bolts sticking out so that the shelf can slide onto them.
NOTE: ALWAYS HOLD SHELVES FROM THE BOTTOM AS THE
SHELF TOP FLIPS OPEN!
6: Slide the shelf onto the bolts, press down on the shelf to secure into the
keyway. Install the remaining three bolts into the shelf before tightening. After all
five bolts are in place, tighten all bolts using a 3/8" socket or wrench.
7: Repeat steps 5 and 6 for the left side of the grill.
8: Lift the hopper lid. Remove the two screws from the back panel as shown and
lift up on the back panel.
9: Route the Ethernet cable connected to the controller side shelf into the back of
the grill. The port is located just below the main wiring harness on the controller
side of the grill. Tighten the strain relief once you have pulled approximately 3
feet of cord into the grill.
10: Route the Ethernet cable behind the auger motor and connect to the Wi-Fi
card. Note: The tab on the Ethernet cord goes towards the front of the grill.
11: Attach the included antenna to the grill by twisting in a clockwise motion. The
antenna will be included in the hardware kit located in the grease tray.
12: Replace the back panel as shown. There are 3 metal tabs on the bottom of the
panel that must be slid into place before securing. Reinsert and tighten included
screws.
13: Attach the main grill harness to the plug in the back of the grill controller box.
14: Reinsert and fasten the shelf pan and shelf tray as shown using the last shelf
bolt included in the hardware kit.
15: Attach the cord wrap with included screws found in the hardware kit. Plug in
the grill using the included power cord.
I
!=jg)
I
I l
I
I
COMPLETE THE STEPS BELOW IN NUMERICAL ORDER, REFERENCE THE SAME NUMBERED
DIAGRAM AND HARDWARE COMPONENTS FOR CLARIFICATION.
I
t
ii
@
ii
·
·
�
/ "
J
7
�
11'
'I
i
(
@:;I
.�
@:;I
D
[Q]
I
I
f
�
(j
Summary of Contents for Pro
Page 1: ......
