65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
Memphis Audio built a 50+ year legacy in the audio industry engineering the highest quality products to produce
the best possible listening experience for our fans and loyal supporters. To fully appreciate our products we
recommend taking the time to read and follow the instructions in this manual. As always, we recommend all
installations and service be performed by an authorized Memphis Audio dealer.
For optimal performance, Memphis recommends using only Memphis Connection accessories. Outfitting
your system with properly sized Memphis Connection wire and accessories will dramatically boost your
listening experience and increase the durability of your Memphis Audio products.
Ready to Turn It Up? Read This First!
Memphis Audio recommends all installations to be performed by an authorized Memphis Audio dealer. If you
chose to proceed with your own installation, please read the following instructions.
• Turn OFF all stereo and other electrical devices prior to beginning the installation
• Disconnect the negative {-} battery lead from your systems battery.
• Locate all fuel lines, brake lines, oil lines and electrical cables when mapping out your installation.
• Check the mounting depth to make sure there is sufficient room to mount the EQ
• When connecting ground points, make certain that all paint is carefully scrapped away from the grounding
location and that the contact is made with bare metal.
• Use a utility knife to trim away fabric from hole locations prior to drilling or cutting. Drilling directly into
fabric can tear and damage fabric beyond the desired installation location.
• When running power cables through sheet metal, be certain to use grommets to insulate the lines from the
metal edges of the sheet metal.
• If possible, use tubing through the grommets for extra protection.
There are two basic mounting options for your MXAZEQ5BT. One is to under-mount the unit beneath the dash
panel using the supplied brackets as shown.
The second option is to flush mount the unit by cutting a hole through a suitable panel for an built-in look. If
you chose the in-dash mounting method, be careful to cut the correct size hole for the best appearance. Also
take care not to let your EQ or the cables interfere with other components in the mounting location.
Installation Instructions
Features
Mounting The Equalizer
Specifications
The MXAZEQ5BT 5-Band marine grade EQ with Bluetooth allows you to dial in your system for peak performance and
control cabin, tower and sub levels from a single unit. The universal 1/2 din design will fit easily in multiple
applications and serve as the command center for your systems audio. This unit is a perfect solution for marine
audio applications.
Main Volume Control With Three Independent Zone Output Controls
Connect up to 3 external amplifiers with separate level output controls from the front panel with a
master volume control for the entire system.
Front Panel Source Selector MAIN/AUX and BLUETOOTH
The front panel source selector control knob allows you to switch between 3 different input sources
(BLUETOOTH, AUX and RCA INPUTS)
5-Band Dual Equalization - Bass, Mid-Bass, Mid and High (BOAT and TOWER)
Each center frequency receives 18dB of boost or cut to adjust
• Bass (75Hz) • Mid Bass (250Hz) • Mids (2kHz) • Mid/High (6kHz) • High (14.5kHz)
USB Charging Port
2 Amp output to charge your connected Bluetooth device.
High Voltage Line Driver
6V of pre-amp signal voltage to deliver clean output signal for your amplifiers. Up to 6V in BLUETOOTH
mode and up to 10V in AUX/MAIN mode.
MOSFET PWM Power Supply
The Pulse Width Modulated power supply is used to provide steady voltage from the vehicles or boats
charging system which can vary under normal operating conditions
Marine Grade Conformal Coated PCB
Conformal coated circuit board resists damage and corrosion from the elements and water.
MXAZEQ5BT
Dual Zone 5-Band Marine EQ
with Bluetooth & Sub Level
Washer
Spring Washer
Washer
Tapping Screw
Spring Washer
Screw
Frequency Response: 10Hz - 50kHz
Frequency EQ Center: 75Hz, 250Hz, 2kHz, 6kHz, 14.5kHz
Total Harmonic Distortion THD: 0.02%
Signal to Noise Ratio: >101dB
Inputs: Switchable, 3-source MAIN, AUX, Bluetooth
Equalization Boost/Cut: -/+18dB
Channel Separation: 85dB
Maximum Output Voltage: MAIN, AUX - 10Vrms @ 0.1%THD | Bluetooth - 6Vrms @0.1%THD
Power Supply: 11-15V DC negative ground
Fuse: 2 Amp (AGC type included)
Dimensions: Chassis 7”W x 1.0”H x 4” D (178mm x 25.4mm x 102mm)
