Meltem M-WRG-S-T Operating Instructions Manual Download Page 27

Page: 27 / 28

Operating instructions

M-WRG-S/Z-T(-F,-FC) ventilation unit

- 27 -

Meltem Wärmerückgewinnung GmbH & Co. KG

Am Hartholz 4 · D-82239 Alling

[email protected] · www.meltem.com

VENTILATION THE RIGHT WAY

V E N T I L AT I O N & H E AT R E C O V E R Y

13 Troubleshooting

Error

Cause

Remedy

Ventilation unit is not running

Ventilation unit is in safe mode

after an EMC fault

Switch the ventilation unit off,

wait 15 seconds, then switch

Installation error

Have the wiring checked by a

qualified electrician

Faulty switch, motor or control-

ler

Check by a qualified electrician

Air flaps do not open after

switching on

After a long stoppage or when

starting up for the first time, the

servomotor is not powered by

the electronic circuit.

Switch the ventilation unit off

and on again

Air flap range of motion is

blocked by foreign bodies

(plaster, polystyrene, etc.)

Carefully remove the foreign

bodies, remove the cover if

necessary (see „11.3.1 Re-

move cover from ventilation

unit“ on page 24)

Ventilation unit starts to beep

at intervals

Air filter is dirty or one-year

interval for filter changes is

exceeded

Change air filters (see „11.3

Changing the air filters“ on

page 24)

The ventilation unit frequently

activates the frost protection

function
“Reduced ventilation” program

LED flashes on the InControl

pushbutton sensor (see sec-

tion 10.1 on page 21)

Fault (e.g. faulty sensor or

motor)

Have the ventilation unit

repaired by Meltem or by an

authorised specialist company

“Normal ventilation” program

LED flashes on the InControl

pushbutton sensor (see sec-

tion 10.2 on page 21)

Air filter is dirty or one-year

interval for filter changes is

exceeded

Change air filters (see „11.3

Changing the air filters“ on

page 24)

“Humidity control” program

LED flashes on the InControl

pushbutton sensor (see sec-

tion 10.7 on page 22)

Humidity of the supply air is

greater than that of the extract

air, dehumidification is not

possible

No intervention required;

ventilation operation is limited

to the lowest ventilation level;

as soon as the humidity of the

supply air drops below the

level of the extract air, dehu-

midification is resumed and the

flashing stops

Summary of Contents for M-WRG-S-T





























Search results

Summary of Contents for M-WRG-S-T

Reviews:

Related manuals for M-WRG-S-T

Brands by name

Popular brands

Meltem M-WRG-S-T, Operating Instructions Manual

Search results

Summary of Contents for M-WRG-S-T

Reviews:

Related manuals for M-WRG-S-T

Brands by name

Popular brands