manualshive.com logo in svg

Meltem M-WRG-II Series, Dismantling Instructions

Share
Download
Meltem M-WRG-II Series Dismantling Instructions Download Page 8

Dismantling instructions 

Ventilation units from the M-WRG-II series

- 8 -

Meltem Wärmerückgewinnung GmbH & Co. KG

Am Hartholz 4 · D-82239 Alling

[email protected] · www.meltem.com

VENTILATION  THE  RIGHT WAY

V E N T I L A T I O N   &   H E A T   R E C O V E R Y

4.6 

Remove the exhaust air and 

supply air fans

Fig. 5: 

Remove the exhaust air and supply air fans

1

2

3

4

 

►

Pull the exhaust air fan (item 1 in Fig. 5) up 

and out.

 

►

Remove the black retaining clip (item 2 in 

Fig. 5) from the exhaust air fan with a slotted 

screwdriver.

 

►

Detach the two plug connectors (item 3 in 

Fig. 5) from the exhaust air fan.

 

►

Remove the exhaust air fan.

 

►

Repeat the process for the supply air fan 

(item 4 in Fig. 5).

4.7 

Remove the sensors 

Fig. 6: 

Remove the sensors

1

1

 

►

Remove the sensors (item 1 in Fig. 6) from 

the holders.

 

►

Detach the sensors from the ribbon cables.

NOTICE

The number of installed sensors will depend 

on the type of ventilation unit.

Summary of Contents for M-WRG-II Series















Reviews:

No comments

Brands by name

Popular brands

Load more brands