manualshive.com logo in svg

Meltem M-WRG-ES, Installation Manual, Page: 14 / 24

Share
Download
Meltem M-WRG-ES Installation Manual Download Page 14

Installation manual 

Outer wall terminals M-WRG-ES, M-WRG-ESR, M-WRG-ESG

- 14 -

Meltem Wärmerückgewinnung GmbH & Co. KG

Am Hartholz 4 · D-82239 Alling

[email protected] · www.meltem.com

VENTILATION THE RIGHT WAY

V E N T I L AT I O N   &   H E AT   R E C O V E R Y

5.1.3 

Attaching the outer wall terminal

 

►

Remove the two cross-head screws (item 1 

in Fig. 9) at the top of the outer wall termi-

nal.

 

►

Slide the cover (item 2 in Fig. 9) up roughly 

10 mm. Lift the cover away from the base 

plate (item 3 in Fig. 9).

 

►

Fully coat the 4 mm wide sealing surfaces 

(item 4 in Fig. 9) on the inside with Vase-

line.

 

►

Carefully position the base plate (item 1 in 

Fig. 10) correctly on the ventilation pipes. 

Be careful not to damage the seals.

NOTE

Make sure that the drip edge (item 2 in Fig. 10) is 

pointing downwards.

 

►

Use a spirit level to align the base plate 

vertically (see item 3 in Fig. 10).

 

►

Use the six screws provided to fix the base 

plate (item 4 in Fig. 10).

 

►

Attach the cover to the base plate.

 

►

Use the two cross-head screws to fix the 

cover (item 1 in Fig. 11).

 

►

Remove the protective films from the cover.

 

►

Clean the outer wall terminal (see section 6 

on page 22).

Fig. 9:  Removing the cover

Fig. 10:  Fixing the base plate

Fig. 11:  Outer wall terminal installed

Summary of Contents for M-WRG-ES

























Reviews:

No comments