1
. Turn ON the appliance:
– if a VCR, insert a cassette
– if SAT, select a program
– if DVD, insert a DVD.
2
. Press and release the TV - VCR - SAT -
DVD selection key for the appliance you
want to use:
– the TV key is used to search only for
the TVs of the brand selected
– the VCR key is used only for the VCRs
– the SAT key is used only for the SATs
– the DVD key is used only for the
DVDs.
3
. Hold down the SHIFT and ON/OFF
keys together until the TV - VCR -
SAT - DVD selection key starts to flash
indicating that the remote control is in
programming mode.
4
. Release the keys. Within 15 seconds,
enter the code 000.
The TV- VCR - SAT -DVD selection key
flashes more quickly to indicate that
the remote control is ready for the
search.
5
. Point the remote control at the
appliance. Press and release
slowly
one of the most frequently used keys
several times
STOPPING
when the
appliance responds correctly to the
command.
Identify and make a note of the code
for the appliance which you have
searched for, following the code
noting procedure (see “NOTING THE
PROGRAMMED CODE” section).
1
. Turn ON the appliance:
– if a VCR, insert a cassette
– if SAT, select a program
– if DVD, insert a DVD .
2
. In the code book enclosed, look
for the brand of the TV-VCR-SAT-DVD
appliance you want to control and
make a note of the first code in the list
BENEATH
the brand previously
identified (e.g. Philips TV 103 - VCR
345, etc.).
3
. Press and release the TV - VCR -
SAT - DVD selection key for the
appliance you want to use.
You cannot set a VCR code using the
TV key.
4
. Hold down the SHIFT and ON/OFF
keys together until the TV - VCR -
SAT - DVD selection key starts to flash
indicating that the remote control is in
programming mode.
5
. Release the keys. Within 15 seconds,
enter the code previously identified
(e.g. TV 103).
Three flashes
indicate
that the code has been saved
correctly. If not, try the code entry
procedure again from
point 3
.
Note down the TV - VCR - SAT - DVD codes
used to program the remote control on the
adhesive label inside the battery cover for
rapid consultation.
NOTE: THE SELECTION KEY STOPS
FLASHING.
The remote control leaves the
programming mode and the TV - VCR -
SAT - DVD selection key stops flashing
• if no keys are pressed for 15 seconds
• if an invalid code is entered
• if you press the TV - VCR - SAT - DVD -
F1 - F2 - F3 - F4 keys by mistake.
DIRECT CODE ENTRY
B
Warning: program one appliance at a time.
1
0
3
0
0
0
GLOBAL SEARCH REMOTE CONTROL PROGRAMMING
C
This operation may take up to about 20 minutes.
Warning: program one appliance at a time.
Additional check
Point the remote control at the appliance.
Check that the appliance responds
correctly to the commands sent. If there
is no response or the appliance only
responds partially or incorrectly, it is
probable that you have used the wrong
code. In this case, try the procedure
again from
point 3
. This time,
however, use the
NEXT CODE
in the list
(e.g. 111 for TV - 348 for VCR, etc.).
NOTE : THE SELECTION KEY STOPS
FLASHING.
The remote control leaves the
programming mode and the TV - VCR -
SAT - DVD selection key stops flashing:
• if no keys are pressed for 15 seconds
• if the code search list is completed
• if you press the TV - VCR - SAT - DVD-
F1 - F2 - F3 - F4 keys by mistake.
6
. When the appliance responds
correctly, press SHIFT to confirm.
Three flashes
indicate that the
operation has been completed
correctly.
Additional check
Check that some of the other functions
used on your original remote control are
working correctly. If the commands
function incorrectly or erratically, you
have probably entered a code for a
similar but different remote control.
In this case, repeat the search procedure
from
point 2
.
TV
DVD
SAT
VCR
TV
DVD
SAT
VCR