background image

9

CAT IV -

 Measurement category IV: Equipment 

connected between the origin of the low-voltage 
mains supply outside the building and the 
consumer unit.

CAT III - 

Measurement category III: Equipment 

connected between the consumer unit and the 
electrical outlets.

CAT II - 

Measurement category II: Equipment 

connected between the electrical outlets and the 
user’s equipment.

 WEEE Directive

The crossed out wheeled bin symbol on the 
instrument and on the batteries is a reminder not 
to dispose of them with general waste at the end 
of their life.
Megger is registered in the UK as a Producer 
of Electrical and Electronic equipment. The 
registration no is; WEE/DJ2235XR.
Users of Megger products in the UK may 
dispose of them at the end of their useful 
life by contacting B2B Compliance at www.
b2bcompliance.org.uk or by telephone on 01691 
676124.
Users of Megger products in other parts of the 
EU should contact their local Megger company or 
distributor.

Battery Disposal

Batteries in this product are classified as Portable 
Batteries under the Batteries Directive. Please 
contact Megger Ltd for instructions on the safe 
disposal of these batteries.
For disposal of batteries in other parts of the EU 
contact your local distributor.
Megger is registered in the UK as a producer of 
batteries.
The registration number is BPRN01235.
For Further information see www.megger.com

Summary of Contents for TPT420














Reviews: