background image

21

ACCESSORIES

Lead set 

Three flexible silicon insulated leads with compact clamp

Safety

Meets the requirements of IEC61010-1 CAT IV 600 V

EMC 

Meets the requirements of IEC61326-1

Operating temperature 

Refer to www.megger.com

Operating temperature 

-20 °C to 50 °C

Storage temperature

-25 °C to 65 °C

Ingress protection (lid closed)

IP65

Humidity

90% RH non-condensing at 40 °C

Dimensions 

305 x 194 x 360 (mm) (12 x 7.6 x 14.2 inches)

Weight

7.1 kg (16lb) approx.

  

 

      Order code

Included Accessories

3 m lead set, medium size insulated clips   

 

1002-531

User guide on CD-ROM 

 

 

 

2000-213

RS232 

cable     25955-025

USB 

cable 

     25970-041

3 x 3 m lead set with large insulated clips   

 

1002-534

Optional Accessories

HV test lead sets

3 x 3 m with  un-insulated small clips 

 

 

8101-181

3 x 8 m with un-insulated small clips 

 

 

8101-182

3 x 15 m with un-insulated small clips 

 

 

8101-183

3 x 5 m with medium insulated clips 

 

 

1002-641

3 x 8 m with medium insulated clips 

 

 

1002-642

3 x 10 m with medium insulated clips 

 

 

1002-643

3 x 15 m with medium insulated clips 

 

 

1002-644

3 x 5 m with large insulated clips 

 

 

1002-645

3 x 8 m with large insulated clips 

 

 

1002-646

3 x 10 m with large insulated clips 

 

 

1002-647

3 x 15 m with large insulated clips 

 

 

1002-648

Control circuit test lead set

2 x 3 m with small insulated clips 

 

 

6220-822

Screened HV test leads

1 x 3 m, with 10 kV screened un-insulated small clips  

6220-834

1 x 10 m, with 10 kV screened un-insulataed small clips 

6220-861

1 x 15 m, with 10 kV screened un-insulated small clips 

6220-833

Summary of Contents for MIT1020/2



























Reviews: