OPERATING INSTRUCTIONS
The system is designed to activate and deactivate
immobilization via a relay. It can be armed and disarmed
simply by keying a programmable security code.
While system is armed, if the ignition switch is turned to
the ON position, the keypad lights will flash and horn will
sound for 15 seconds (If horn honk output is connected).
FACTORY DEFAULT DISARMING CODE
: 123456
PASSIVE ARMING (AUTOMATIC ARMING)
1. When the ignition key is turned to OFF, the system will
automatically enter ARMED MODE after 30 seconds.
2. The blue LED will blink slowly to indicate the status.
ACTIVE ARMING (USER ARMING)
1. When the ignition key is turned to OFF, press * then #.
2. The keypad will chirp two times and system will enter
ARMED MODE.
3. The blue LED will blink slowly to indicate the status.
DISARMING
1. Press * then enter your code then press #.
2. The keypad will chirp two times to indicate the correct
code was entered.
3. Within 15 seconds, turn the ignition to ON. System will
disarm and blue LED will turn off.
4. Before pressing #, if you realize you entered an
incorrect digit, press * to re-enter the code.
5. If an incorrect code is entered, the keypad will chirp
four times and will sound the horn once (If horn output
is connected).
6. If incorrect codes are entered three times consecutively,
the keypad lights will flash and the horn will sound for
15 seconds (If horn honk output is connected). The
blue LED will flash rapidly two times then turn off and
system will be in LOCKOUT MODE for 3 minutes.
PROGRAMMING DISARMING CODE
The keypad can be programmed with a custom disarm pin
code that can be changed to increase security level.
To change disarm pin code:
1. Disarm the keypad and leave the ignition ON.
2. Within 15 seconds, press * then enter your new custom
code then press #.
3. The keypad will chirp two times meaning the new code
has been confirmed and stored.
4. The disarm code can be 4, 5, or 6 digits in length.
PANIC MODE
NOTE:
This feature will only sound the horn if the horn
honk output is connected to the vehicle.
1. While ignition is ON or OFF, if the user senses they are
in danger, they can activate PANIC MODE.
2. To activate PANIC MODE, press and hold # for 3
seconds.
3. The keypad lights will flash and the horn will sound for
15 seconds.
VALET MODE
1. Disarm the keypad and turn the ignition to OFF.
2. Within 30 seconds, press * then enter your code then
press #.
3. The keypad will chirp three times and system will enter
VALET MODE. The blue LED will stay on solid whether
ignition is in the ON or OFF position.
4.
Exit VALET MODE:
Turn the ignition to ON, and within
30 seconds, press * then #. The keypad will chirp three
times, indicating system has exited VALET MODE. The
Blue LED will turn off.
NOTE:
In VALET MODE, the vehicle is not under
immobilization protection and can be started freely.
EMERGENCY OVERRIDE (OPTIONAL FEATURE)
NOTE:
If you do not want this feature, do no wire a toggle
switch (Should be rated 3A 250V AC / 6A 125V AC).
IMPORTANT:
Place the SPST on/off toggle switch in a
hidden location so an intruder cannot access it.
87a
85
30
86
Orange wire keypad
“Start”
“On”
White wire
X
Cut
Red wire
Orange wire
“Acc”
“Off”
Starter
Yellow wire to
Ignition Switch
Yellow wire keypad
Connect one wire of an optional toggle switch to the
orange wire from the keypad. Connect the other wire from
the toggle switch to terminal 86 of the starter disable relay.
If keypad has failed or customer has forgotten their code
and cannot disarm the system:
1. Flip the toggle switch to OFF to override the system.
2.
Exit EMERGENCY OVERRIDE:
Flip the toggle switch
to ON to exit override mode.
MEGATRONIX
WWW.MEGATRONIXUSA.COM
COPYRIGHT © MEGATRONIX, CA U.S.A.
