DVB-T 30
user manual
Introduction:
This is a special designed antenna for both analog and digital terrestrial TV broadcasting reception. It
Can receive all the TV signals of your area in VHF and UHF band, as well as the FM radio signal. It is the
best solution for home reception and digital portable TV reception. It is very practical to install and very
easy to use.
Setting and connection
• Connect the AC 230V cable (1) to the 230V AC wall socket.
• Connect the TO TV cable (2) to the antenna-input socket of your TV or terrestrial digital set-top-box.
After checking that all the connections have been done properly, turn clockwise the on/off knop (4) to
switch the antenna on. LED (3) lights up showing that the amplifier of indoor antenna is working. Now,
turn on your television set on and select a TV programme. then adjust the rod antennas (6), the dipole
antenna (5) and the amplifier gain (4) according to what is described in next paragraphs.
Signal reception
VHF SIGNALS - I-III BAND (channels 1-12)
This antenna receives VHF signals (both analog and digital) through the rod antennas (6).
For best reception, adjust rod antennas as follow:
• For BAND I: extend completely the rod antennas
• For BAND III: shorten the rod antennas to about 16 inches (the extension de pends on the channel
you want to receiver)
• then, move the rod antennas until you get the best signal reception.
UHF SIGNALS - IV-5 BAND (channels 21-69)
This antenna receives UHF signals through dipole antenna (5).
For best reception, adjust rod antennas as follow:
• tilt the dipole up and down
• turn the diplo sideways until you get the best signal reception
Gain adjusting
In order to adjust the amplifier gain turn on/off knob (4) until to get the best signal reception:
• to increase gain, turn the knob clockwise
• to reduce gain, turn the knob anticlockwise
Note:
This antenna can be used directly connected to TV or terrestrial set-top-box, please take
reference of following 2 different connecting ways to install your antenna.
(Fig. 1) Directly connected to TV
(Fig. 2) Directly connected to terrestrial set-top-box
Technical Data:
• Frequency range: VHF 87.5 - 230 MHz
UHF 470 - 862 MHz
• Receiving range: UHF / VHF / FM
• Max. gain:
VHF 30 dB / UHF 30 dB
• Output level:
max. 100 dBµV
• Out Impedance: 75 Ohm
• Noise figure:
< 3 dB
• Power supply:
AC 110V / 230V
Product Features:
• Variable gain control
• Power on/off LED indicator
• SMD circuit technology design
• Built-In high gain and low noise amplifier
• Adjustable loop aerial for the best UHF reception
• Adjustable telescopic antennas for optimum VHF and FM radio reception
• Specially compatible with HDTV of various digital terrestrial signal
(DVB-T, ISDB-T, DMB-T/H, ATSC) and DAB/FM radios.
Installation:
Note: For the best reception, please check the following conditions.
1. Keep the antenna away from the sources of interference: Keep the antenna away from those big
power consumption devices, such as air conditioner, elevator, hair dryer and microwave oven etc.
2. Place the antenna near windows when use the antenna in indoor environment.
3. Install the antenna as high as possible: In digitalterrestrial reception, if there are some interceptions
between antenna and transmission tower, it will cause the signal loss temporarily. So if the antenna
is installed as possible, those interceptions will be reduced.
(1) Power plug
(2) Signal output
(5) Tilt UHF loog
for receiving
channels 21-69
can be turned 360°
(3) Power indicator light
(4) Control knob
(on/off and gain adjustment
(6) VHF telescopic antenna
for receiving channels 1-12
Can be turned up and down (within 180°)
or sideways (within 180°)
Fig. 2
Fig. 1
