1. Bereiten Sie den Kleber für die Montage vor.
2. Tragen Sie nun den Kleber auf die Unterseite
des Antennenfußes in Schlangenlinien auf, da-
mit der Kleber bis ins Innere gut aushärten kann.
3.
Setzen Sie nun sofort (innerhalb von 5 Minuten nach Kleberauftrag) die Anten
-
ne auf das angezeichnete Feld. Drücken Sie den Fuß leicht und gleichmäßig
an und fixieren Sie die Antenne, damit sie nicht verrutscht, z.B. durch ein Kle
-
beband. Es müssen sich nach dem Andrücken noch mindestens 2 mm Kleber
zwischen Antennenfuß und Oberfläche befinden. Der Kleber ist nach max. 48
Stunden bei +18° C und einer relativen Luftfeuchte von 50% ausgehärtet. Soll
-
te während der Montagezeit eine geringe Luftfeuchtigkeit herrschen, sprühen
Sie nach dem Verkleben in der Umgebung der Antenne immer wieder etwas
Wasser in die Luft.
4. Entfernen Sie die evtl. ausgetretene Klebemasse sofort mit einer Spachtel oder
Ähnliches und säubern Sie die verunreinigten Flächen mit dem Reiniger und
einem Vliestuch.
5. Zur Sicherheit können Sie den Antennenfuß zusätzlich befestigen. Dazu bohren
Sie durch die vorhandenen Löcher im Antennenfuß in das Dach Ihres Fahrzeu-
ges und fixieren es durch eine Schraube mit Kontermutter. Damit der frisch
verklebte Fuß nicht verrutscht, warten Sie mit dieser Arbeit bis der Kleber aus-
gehärtet ist.
6. Nach der kompletten Montage und Aushärtung des Klebers, kann eine Silikon-
fuge um den Antennenfuß gezogen werden.
2. Installation
06
DEUTSCH
5. Rauen Sie die gezeichneten Flächen und Füße mit Schleifpapier (120er Kör-
nung) leicht an und säubern Sie die Fläche erneut mit dem Reiniger und
lassen Sie den Reiniger ca. 10 Minuten ablüften.
ACHTUNG:
Flächen an-
schließend nicht mehr berühren.
6. Montieren Sie die Dachdurchführung (am besten im Windschatten hinter
der Antenne) auf dem Fahrzeugdach. Es ist darauf zu achten, dass das Ein
-
dringen von Wasser und Feuchtigkeit (z. B. Regen oder Spritzwasser) im
Bohrloch vermieden werden muss. Achten Sie darauf, dass die Kabel nicht
zu sehr gebogen werden um Signalverlust und eine Beschädigung des Ka-
bels zu vermeiden (kleinster Biegeradius max. 5-7 cm).
2.2 Klebeanleitung
Summary of Contents for Campingman Kompakt 3
