1. Second Vehicle Security Operation:
Your remote transmitter can be utilized to control a second
vehicle security system. To program the remote control transmitter to a second vehicle, follow the
instructions for Transmitter programming. All programming parameters be the same except for the following:
For Regular Remote Control Transmitter:
1. Prior to pushing any button on the transmitter. Press the Select
II
button first on the transmitter.
2. Once
II
button is pressed the LED on the transmitter will illuminate for 3.5 seconds to indicate the
second transmitter pin code has built-in.
3. While the LED is illuminated, press any button on the remote control transmitter to control a second
vehicle security system.
For 2-way LCD Remote Control Transceiver:
2nd
Car Operation:
While the “
II
” icon display on the LCD screen, you can remote control and communicate
with a second vehicle security system. It has
two
short “bi” sounds while pressing the button of the LCD
screen transceiver.
1. Press and hold
and
buttons at the same time until
one long beep is heard.
Programming has now been entered.
2. Within 5 seconds press & hold
button until
two
beep sounds are heard & the
“
II
” icon will display on LCD screen indicating 2nd transceiver pin code has built-in.
3. To exit programming mode, take no action for five seconds. The remote control will
generate two long beeps to indicate programming mode has been exited.
Back to 1st Car Operation:
You can remote control and communicate with a first vehicle security system. It
has
one
short “bi” sound while pressing the button of the LCD screen transceiver.
1. Press and hold
and
buttons at the same time until
one long beep is heard.
Programming has now been entered.
2. Within 5 seconds press and hold
button until
one
beeping sound is heard.
3. To exit programming mode, take no action for five seconds. The remote control will
generate two long beeps to indicate programming mode has been exited.
2. Vibration / Melody Mode:
It is useful when you are in a noisy place and difficult to hear beep sound from
the remote control as the remote control in this mode, vibrates it if your security system is triggered.
1. Press and hold
and
buttons at the same time until
one long beep is heard.
Programming has now been entered.
2. Within 5 seconds, press the
button to select the mode of vibration or melody, the
icon will displayed on the LCD screen to show the LCD remote transceiver is on
vibration mode.
3. To exit programming mode, take no action for five seconds. The remote control will
generate two long beeps to indicate programming mode has been exited.
3. Power Save Mode:
While the power save mode, the LCD remote transceiver “sleep” until a button is
pushed, extending the life of battery. When power save mode is “Off”, the remote control will wake up
periodically to check for messages from the security module..
1. Press and hold
and
buttons at the same time until
one long beep is heard.
Programming has now been entered.
2. Within 5 seconds, press the
button to toggle “On” or “Off”. The remote will beep
once for “On”, twice for “Off”. When power save mode is “On”, the
icon on
the LCD screens to indicate entry the “power save mode”
3. To exit programming mode, take no action for five seconds. The remote control will
generate two long beeps to indicate programming mode has been exited.
4. Screen Lamp ON:
Press the
button once, the LCD screen lamp will turns on for 5 seconds
5. System’s Status Check
When you want to check the system’s present status
through the LCD screen, Press the transceiver
button first, within 3 seconds press
and
buttons at the same time. It responds with one melody sound, the LCD
screen should be illuminated.
Note:
If it has no responds then you are out of range.
6. Clear the Flash Icon and Melody Sound:
Press the
button first, within 3 seconds press
and
buttons at the same time. It will clear the flash icon and melody sound on the LCD screen transceiver
7. Stop The Trigger Melody Sound:
While triggering the alarm the LCD screen will alert user through
melody sound and flashing trigger icon, press any button on the LCD remote transmitter to stop melody
sound
only, the remote control buttons will not send a command to the system.
10
