Meech Hyperion 907 Operating Manual Download Page 17

Repairs And Warranty

The Hyperion power supply is warranted by Meech Static Eliminators Ltd to the 
original purchaser against defects in the material and workmanship for two years after 
shipment. Should any malfunction occur, please return the power supply directly to 
Meech Static Eliminators or your local distributor. All products returned to the factory 
MUST be accompanied by a return authorisation number and must be shipped 
prepaid. For prompt service, ship the unit to the factory with the return authorisation 
number shown clearly on the label. Be sure it is well packed in a sturdy carton with 
shock absorbing material.

Include a note stating the nature of the problem as specifically as possible, and also 

include instructions for returning the power supply to you. We will pay one-way return 
surface shipping costs on any repairs covered under the warranty.

Field repairs should not be undertaken under the warranty period. Repair attempts by 

unqualified personnel will invalidate the warranty.

CE Approval

A CE Declaration of Conformity for this product exists in respect of the Low Voltage 
Directive:72/23/EEC (“LVD”) & Electromagnetic Compatibility Directive: 89/336/EEC 
(“EMCD”) 

Health and Safety

Emission of Ozone: Considerably below international standard of 0.1ppm

 

 

       

Summary of Contents for Hyperion 907





















Reviews: