background image

 

                                                                                       

 

 

 

  16

16

16

16  

 

 

 

9. CHECK AND MAINTAIN

 

 

Warning 

 Check and maintain the game by technicians.   

Please power off the game when check and maintain.   
Please do not put any tools into cabinet, otherwise it will cause problem.   
After checking, please tightly screw the screws and close the door.

 

 

 

 

 

 

Daily Check

 

ITEM

 

DESCRIPTION

 

COIN MECH 

Check whether the coin mech work properly. 

MONITOR 

Check if the monitor works properly. 

SOUND 

Check whether the sound and volume are ok. 

PUMP 

Check if the pump works properly.

 

TEMPERATURE 

HUMIDITY 

Check if the temperature and humidity is proper 

 

 

Daily Maintenance 

 

 

 

ITEM

 

DESCRIPTION

 

Periodically 
check

 

PUMP 
INTERFACE 

Check all the interfaces of the pump to see 
if there is water leakage 

Every 3 
months 

WATER 

Check if the water is clean, if not, please 
change the water. 

Every 2 

weeks 

ITEM

 

DESCRIPTION

 

THE CABINET 

Clean the cabinet with water and soft paper. 

MONITOR 

GLASS 

Clean the monitor and glass with water and soft 
paper.   

PCB 

Sweep  the  dust  and  dirty  in  the  board  with 
small brush 

Summary of Contents for Kiddie Firemen



















Reviews: