Mecademic Meca500 R3 Programming Manual Download Page 76

Page: 76 / 110

Programming manual for Meca500 (for firmware 9.2.x)

COMMUNICATING OVER CyCLIC PROTOCOLS

ROBOT STATUS CONTROL FIELDS

Field

Type

Description

Deactivate

Bool (action)

Deactivates the robot when set to 1.

Activate

Bool (action)

Activates the robot when set to 1 (only if Deactivate bit is 0).

Home

Bool (action)

Homes the robot when set to 1 (if the robot is activated but not

homed).

ResetError

Bool (action)

Resets the error when set to 1.

SimMode

Bool (state)

Enables (when set to 1) or disables (when reset to 0) the simulation

mode (only applied when the robot is deactivated).

RecoveryMode

Bool (state)

Enables (when set to 1) or disables (when reset to 0) the recovery

mode.

Table 5:

Robot control fields

3.4.2 Motion control

Table 6

lists the fields that control the motion of the robot.

MOTION CONTROL FIELDS

Field

Type

Description

MoveID

Integer

A user-defined number, the change of which triggers the addition of the

command specified in MotionCommandID to the motion queue.

SetPoint

Bool (state)

Has to be set to 1 for motion commands to be sent to the robot.

PauseMotion

Bool (state)

Puts the robot in pause without clearing the commands in the queue. Motion

is resumed once both the Pause-Motion and ClearMotion bits are reset to 0.

ClearMotion

Bool (action/

state)

Clears the motion queue and puts the robot in pause. Motion is resumed once

both the PauseMotion and the ClearMotion bits are reset to 0.

ResetPStop

Bool (state)

Resets P-Stop 2.

Table 6:

Motion control fields

3.4.3 Motion parameters

The motion parameters include the MotionCommandID and six corresponding arguments. These are

illustrated in

Table 11

. The list of available MotionCommandID values is given in

Table 8

along with

arguments usage in each case.

MOTION PARAMETERS

Field

Type

Description

MotionCommandID Integer MotionCommandID (see

Table 8

Motion command

argument 1

Real

First argument of the motion command, if applicable, as described in

Section 2

Motion command

argument 2

Real

Second argument of the motion command, if applicable, as described in

Section 2

Summary of Contents for Meca500 R3















































































































Search results

Summary of Contents for Meca500 R3

Reviews:

Related manuals for Meca500 R3

Brands by name

Popular brands

Mecademic Meca500 R3, Programming Manual

Search results

Summary of Contents for Meca500 R3

Reviews:

Related manuals for Meca500 R3

Brands by name

Popular brands