background image

6

Ventilating the Tent

Proper ventilation is the key to minimizing condensation in any tent. Keep 

fabric doors open as widely as the prevailing weather permits. If bugs 

or drafts aren’t a problem, leave mesh doors open too. Crack each door 

open from the top down; warm, moist air rises and will escape through 

high openings. If the design of your tent allows for it, have openings at 

both ends or both sides of the tent to allow air to fl ow through for best 

ventilation. On very hot nights, when you are confi dent there will be no 

rain or dewfall, you can leave the fl ysheet off and use the inner tent alone 

as a “bug tent.” 

Disassembling the Tent

The most important consideration in taking down a tent is not to stress 

the poles and fabrics. First, disconnect guylines and release the tension 

from the tent. Next, release all the poles. If your tent has pole sleeves, 

push the poles out of the sleeves instead of pulling them out. To minimize 

the stress on the bungee cord in the poles and to speed disassembly, 

fold each pole in half fi rst, and then fold down towards the outsides, two 

sections at a time.

Packing the Tent

If possible, fold and roll the tent rather than stuffi ng it into its sack—rolling 

makes a smaller package, and causes fewer creases in the polyurethane 

coating. The tent and poles may be carried separately for easier packing 

or load sharing. There are two drawcords on the tent sack. Use the lower 

one when carrying the tent separately from the poles; this makes a 

shorter package that fi ts sideways into a pack. If carrying the pole sack 

on the outside of a pack, securely attach the drawcord to the pack to 

avoid loss.

 

CARE AND MAINTENANCE

Protecting the Tent

Ultraviolet damage is the single largest hazard your tent faces in its 

lifetime. Fabrics should not be exposed to sunlight for extended periods 

of time; this will eventually result in colour fading and fabric failure. The 

uncoated fabrics of the tent canopy are most susceptible to damage from 

UV and should be covered by the more durable fl y. If extended exposure 

is unavoidable, cover the tent with a tarp or a sheet of nylon.

Nunatak eng.indd   6

Nunatak eng.indd   6

3/1/05   2:28:56 PM

3/1/05   2:28:56 PM

Summary of Contents for Nunatak









Reviews: