background image

BUILT-IN GAS HOB

INSTALLATION AND USER  INSTRUCTIONS 

Note: Do not use the hob until you have read the instruction manual.

Reference to AS/NZS 5601

Cod:

1. INTRODUCTION

 

(*) Air inlet  minimum section: 100cm

2

Fig. 1                                                Fig. 2                                                Fig. 3

UNPACKING THE APPLIANCE

Remove all packaging and make sure the appliance is in perfect condition. 

If you have any doubts, do not use the appliance and call your supplier..

Some parts on the appliance are protected by a plastic film. This protective film must be removed 

before the appliance is used. 

1

2

3

Even if you have used a gas hob before, it is important that  you read these instructions thoroughly  

before using the appliance, paying particular attention to the installation and safety instructions. If you

have any problems installing, operating or cooking with your hob, please check through these

instructions to ensure all of them have been adhered to.

WARNING!   For your own safety, make sure that these instructions on installation, use and 

maintenance are followed.

Please keep these instructions in a safe place for future reference.

Should the appliance be sold or transferred, please pass on these instructions to the new owner

.

3. CLEANING AND MAINTENANCE

                                            4.  SAFETY INSTRUCTIONS

Make sure that this instruction booklet is read thoroughly and understood before attempting to install or 

operate this hob.

The instructions are provided in the interest of your safety. 

GAS SAFETY REGULATIONS AND USE OF YOUR HOB

1.       It is a legal requirement that all gas appliances are installed by qualified personnel only in accordance 

with current legislation.  It is your responsibility to ensure compliance with the law.

2.       Repairs or servicing of this product must only be carried out by an authorised service agent using 

approved parts.

3.       No attempt must be made to modify this appliance under any circumstances.

4.       Cooking appliances can become very hot in use – please keep children and pets away from them.

5.       Do not allow children to operate or play with any part of the appliance.

6.       Do not use unstable pans and ensure that the handle is positioned away from the edge of the worktop.

7.       In the interest of hygiene and safety, please ensure the hob is kept clean.

8.       This appliance is designed for domestic cooking only.   Commercial use will invalidate the warranty.

9.       Do not cover the hob or place combustible materials on or near the surface even when the hob is not in 

use.

10.    Do not fill deep fat frying containers more than one third full of oil and NEVER  leave unattended.

11.    Before cleaning the hob, switch off at the mains.

12.    When cooking is finished, switch off all controls and allow to cool.

13.    These appliances are not intended for use by persons (including children) with reduced physical, 

sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision 

or instruction concerning use of the appliance by a person responsible for their safety.

14.    If the supply cable  is damaged, it must be replaced by the authorised service agent or qualified person only.

15.    Do not immerse the appliance or the power cable into water or any other liquid.

16.    DO NOT SPRAY AEROSOLS IN THE VICINTY OF THIS APPLIANCE WHILE IT IS IN OPERATION.

17.    DO NOT USE OR STORE FLAMMABLE MATERIALS ON OR NEAR THIS APPLIANCE.

18.    DO NOT PLACE ARTICLES ON OR AGAINST THIS APPLIANCE.

19.    DO NOT MODIFY THIS APPLIANCE.

                                         5. INSTALLATION INSTRUCTIONS

TECHNICAL INFORMATION

The installation, adjustments, conversions and maintenance listed in this section must be carried out by 

qualified personnel only.

The safety and automatic adjustment devices of the appliance may only be modified by an authorised service 

agent.

The installation of this gas hob must comply with Australia and New Zealand standards.

This appliance must be fitted in compliance with the installation rules given above.  Also, particular attention 

must be given to the following requirements for ventilation.
INSTALLATION LOCATION

The appliance may be located in a kitchen, kitchen/diner or utility room, however, it cannot be in a 

room containing a bath or shower.  

WARNINGS

Comply with the following instructions, before remounting the parts:

-Check that the heads burners and the relative burner caps, are correctly positioned in their 

housings.

-Check that burner head slots have not become clogged by foreign bodies.

-If to happened installation or after a few fimes, you find a tap is difficult to open or close do 

not force it but call for technical assistance urgently.

-After use, to keep them in good condition, the plates should be treated with specific 

products, easily found in the shops, to keep the surfaces clean and shining. This will also 

prevent rust from forming.

-If any liquid spills over it must always be removed with a sponge.

VENTILATION RECOMMENDATION

The room must have an opening window or equivalent, some rooms may also require a permanent 

vent.  If the room has a volume between 5-10m

3

, it will require an air vent of 50cm

2

 effective area, 

unless it has a door which opens directly to the outside.  If the room has a volume of less than 5m

3

, it 

will require an air vent of 100cm

2

 effective area (Fig. 1). 

When using more than one hotplate at once, open a window if a mechanical extractor is not present or 

working (Fig. 3).

The packaging materials should be carefully discarded and not left within easy reach of children as they 

are a potential hazard.

INSTALLING AND FIXING THE HOB (QUALIFIED PERSONNEL ONLY)

The appliance can be fitted to any worktop with a thickness of 40mm or 50mm.

No overhanging surface or cooker hood from Hob should be 650mm

Fix the appliance in position (Fig. 4).  The sides of the adjacent cabinets above may be lower than 

650mm down to 400mm, provided they are heat and steam resistant.

These hobs are supplied with a special seal which prevents liquids from seeping underneath the 

appliance. Follow these instructions in order to correctly fit this seal:
Detach the seals from their backing ensuring that the transparent protection still adheres to the seal.  

Turn the hob over and correctly position seal *S* (Fig. 5) under the edge of the hob so that the outer 

part of the seal perfectly matches the outer edge of the hob. The ends of the strips must fit together 

without overlapping. Fix the seal to the hob evenly and securely, pressing it firmly in place.

MGH70B

The surface of the hob need to be cleaned after each time they used.

Dayly cleaning

VITREOUS  ENAMEL

ALUMINIUM

Hotplate burner bodies.

Similar to paint cleaning above. Use a nylon brush to remove any cleaning materials, water or dirt 

from the hotplate burner bodies. After cleaning, wipe dry and refit to the hob ensuring they are 

correctly seated.

Check parts are reassembled correctly by lighting the burners and allowing to dry out.

PLASTIC

Control knobs.

Wipe with a cloth wrung out in hot soapy water.

STAINLESS STEEL

Cloth wrung out in hot soapy water

Never clean when the top and components are still warm.Do not use metal or abrasive pads,abrasive 

powders or corrosive spray products.Never leave vinegar,coffee,milk,salty water,lemon or tomato 

juice for any length of time on the surfaces.

Hotplate

 burner caps

 pan supports

enamelled burner 

caps 

C

and burner heads 

T

See right figure.

Cloth wrung out in hot soapy water. Stubborn stains.can be 

removed with a cream paste.

approved by the Vitreous Enamel Development Council, liquid 

cleaner or by rubbing with fine steel wool soap pads.

NOTE: The pan supports can also be cleaned in the 

dishwasher.

MGH90B

MGH70B

MGH90B

MGH70B

MGH90B

2. YOUR HOB

Applicable for Gas

Rapid 

gas 

burner 

Semi-rapid

gas

burner

burner

Auxiliary

gas

Material

Flame

failure

device

Power

Supply

Size

(mm)

Built-in

 (mm)

Type

510x700x100

510x860x100

220-240V~ 

50Hz

Yes

Triple flame

 gas burner

Glass

Glass

13.7 MJ/h

6.3 MJ/h

3.6 MJ/h

477x557

Yes

13.7 MJ/h

10.8 MJ/h

10.8 MJ/h

6.3 MJ/h

3.6 MJ/h

477x832

Triple flame gas burner 13.7 MJ/h

10.8 MJ/h

Rapid

gas burner

3.6 MJ/h

Auxiliary

gas burner

6.3 MJ/h

Semirapid  

gas burner

6.3 MJ/h

Semirapid  

gas burner

6.3 MJ/h

Semirapid  

gas burner

6.3 MJ/h

Semirapid  

gas burner

Triple flame gas burner 13.7 MJ/h

10.8 MJ/h

Rapid

gas burner

3.6 MJ/h

Auxiliary

gas burner

Unit: mm

Fig. 5

S

S

F

G

400 650min 

A B

C

D

E

557 477 50min  150min  90min 

F

G

400 650min 

A B

C

D

E

832 477 50min  150min  90min 

Rear wall should be a flame retardant material

Fig. 4

D

D

A

B

E

F

G

Front edge of worktop

C

MGH70B

MGH90B

Reviews: